Stevens AeroModel PuddleBug 2.4 Скачать руководство пользователя | Manualshive

Страница: 1 / 12

background image

PuddleBug

Micro RC Model for Spektrum / ParkZone 2.4 systems

Length 10.5 inches | Span 17.75 inches | Wing Area 71 inches

2

| Flying Weight 1.1 oz.

Version 01/06/2010

PuddleBug © 2010 Stevens AeroModel all rights reserved.

Page 1 of 13

2.4

1
2
3
...
»

Содержание PuddleBug 2.4













Отзывы:

Нет отзывов

Похожие инструкции для PuddleBug 2.4

Бренд: Jamara Страницы: 16

Бренд: 4-Max Models Страницы: 8

Бренд: 4-Max Страницы: 38

Бренд: GAME OF BRICKS Страницы: 30

Бренд: Radica Games Страницы: 2

Бренд: Radica Games Страницы: 2

Williams ALCO PA-1

Бренд: Bachmann Страницы: 8

Branchline Class 03

Бренд: Bachmann Страницы: 3

Бренд: Omegon Страницы: 134

Бренд: Kayoba Страницы: 21

St. Bernard Puppy

Бренд: Enabling Devices Страницы: 2

Бренд: Faller Страницы: 4

Бренд: Eduard Страницы: 4

Seenotrettungsboot

Бренд: GRAUPNER Страницы: 30

midnight gambler 21005

Бренд: GRAUPNER Страницы: 40

Бренд: LGB Страницы: 32

Бренд: Mochtoys Страницы: 2

Бренд: QABA Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды