WOOFER DRIVER TWEETER
2x100µF 2x10µF
V1000.1 ES(1Ω) 450W/2ohms 125W/8ohms 150W/8ohms
V1000.1ES(2Ω) 450W/4ohms 125W/8ohms 150W/8ohms
SPEAKER TABLE
V1000.1 ES (1Ω) 2 x 450Wrms / 2 Ohms
V1000.1 ES (2Ω)2 x 450Wrms / 4 Ohms
AMPLIFIER IS FOR A SUBWOOFER,
WOOFER, DRIVER AND ALL SPEAKER
THAT RESPONSE UNTIL 20KHZ.
V1000.1 ES(1Ω) 900Wrms/2ohms
V1000.1 ES(2Ω) 900Wrms/4ohms
OBS:
450Wrms per bobina.
2 x 10
*
Fuse
MAX
30 cm
*Fusel MAXI 50A
TWEETER
PHENOLIC
DRIVER
POWER Watts RMS
AUDIO INPUT AND CONTROLS
GENERAL DESCRIPTION
OUTPUT AMPLIFIED AUDIO AND POWER INPUT.
1) INPUT – RCA R and L:
This entry should receive the signal via RCA cable that should be
connected to the output RCA of CD/MP3-player.
2) LEVEL – GAIN CONTROL:
Controls the level of the input signal, allowing a proper adjustment to
any CD/MP3-player of the market. Can be regulated as follows:
a)
at CD/MP3-player, put any musical signal and set the volume at 80% max.
For example: if the maximum volume of your CD/MP3-player is 45 (100%) , set to 36 (80%).
b)
at amplifier, from the LEVEL in the minimum, increase gradually up until distort the signal.
c)
slowly, return LEVEL until the signal is free of distortion.
3) HIGH PASS FILTER:
This control varies the filter cut off frequency from 15Hz to 2KHz. This filter
allows to pass sounds above the cut off frequency.
4) LOW PASS FILTER:
This control varies the filter cut off frequency from 50Hz to 15KHz. This filter
allows to pass sounds below the cut off frequency.
5) OUTPUT SPEAKERS:
Beware the correct polarity of connections to the speakers, check the
minimum output impedance. Use cables of at least 4 mm².
6) REM – REMOTE ACTUATION:
Connect the REM terminal to output remote/electrical antenna of
your CD/MP3-player. So, when turn on your CD/MP3-player, the amplifier will automatically turn
on too. Cable of 0.5 mm² is enough.
7) GND – EARTH CONNECTION:
Use cable gauge of 21,0 mm² (AWG 4). Plug the cable into the
vehicle chassis.
Note: always connect the wire GND (-) of CD-player, or others apparatus at the same
point.
8) BAT – POSITIVE:
Connect the terminal (BAT) to the positive pole of battery (+12V) with a cable
(gauge at least 21,0 mm² (AWG 4)). It is extremely important that use a fuse or breaker
protection in this cable with a maximum distance of 30 cm from the battery.
short-circuit the terminals of fuse, this may cause irrecoverable damage and loss of warranty.
For installation, choose cables with gauge 21mm²
(AWG 4). The positive cable should come directly
from the battery, with a fuse or circuit breaker
protection located with 30 cm from the battery. The
negative cable should have the same gauge of
positive, screwed into the vehicle chassis, taking
care to avoid paint and rust that may prevent the
passage of electric current, causing power loss and
noise in the sound.
INSTALLATION OF POWER (BATTERY)
INSTALLATION OUTPUT OF SPEAKERS
The cables of the speakers should be polarized (marked) to facilitate identification of positive and
negative. Minimum gauge is 4mm². Keep the cables from the speakers properly insulated.
Beware of metal parts that can damage the insulation of cables.
2 SPEAKERS
1 SPEAKER - DUAL COIL
TRIO WITH 2 WOOFERS, 2 DRIVERS AND 2 TWEETERS
REMOTE
BATTERY
12V
4
5
7
6
