W
ARNING:
ALL
PERSONS
USING
THIS
EQUIP
MENT
MUST
READ
AND
UNDERST
AND
ALL
INSTRUC
TIONS.
FAIL
URE
TO
DO
SO MA
Y RESU
LT
IN SERIOUS INJU
RY
OR DEA
TH. USERS SHOULD
BE
FA
MILIAR WITH
PERTINENT
REGULA
TIONS
GOVERNING THIS
EQUIP
MENT
. ALL
INDIVIDU
ALS WHO
USE THIS
PRODU
CT
M
UST
BE
PROPER
LY
INSTRU
CT
ED
ON
HOW
TO
USE
THE
DEVICE.
AVOID
CO
NT
AC
T
WITH
PHY
SICAL
HAZARDS
(T
HERMAL,
CHEMICAL,
ELEC
TRICAL,
ET
C.). MAKE ONL
Y CO
MP
AT
IBLE
CO
NNEC
TIONS.
Compliance: OSHA
1926.502 & 1910.66
DO NOT REMOVE
Stainless Steel,
Aluminum, Zinc Plated Copper
,
drill
.75”
Ø
(A)”
min from an
y edge
(B)”
TAP!!!
DO NOT REMOVE
WARNING LABEL!
May be used as an anchor point for a leading edge
restraint system. See optional anchor points below for
example. The use of two anchors is not required for
leading edge restraint systems unless otherwise speci-
fied by the manufacturer.
WORK SURFACE
OPTIONAL
(ANCHOR POINTS)
WORK SURFACE
(ANCHOR POINT)
Concrete must be
3000-psi or higher and
fully cured. Installation
location to be approved
by a qualified person.
MINIMUM CLEARANCE 3ft (1m)
DECK/FLOOR/GROUND LEVEL
W
ARNING!!! SWING F
ALLS M
AY OC
CUR
WHEN
THE
W
ORKER IS NO
T DIREC
TL
Y UNDER ANCHOR POINT
.
All products subjected to fall arresting forces should be removed
from service immediately!
1.25” (31mm)
Cleaning Bushing
5” (127mm)
End Termination
Stop Sleeve
11.5” (293mm)
Heavy Duty Return Wire
Spring
Trigger
Anchor Loop
3” (76mm)
2” (50.8mm)
Spoon
Main Cable
DRILLING & INSTALLATION INSTRUCTIONS:
1.
Drill a .75” (20mm) diameter hole at least 3.5” (89mm) deep. The drilled hole must be straight and perpendicular
to the surface. Make sure the hole is of uniform diameter and free of peaks and valleys on the inner wall.
2.
Blow hole clean with compressed air.
3.
Always inspect the hole carefully when reusing a previously drilled hole.
4.
When placing anchor, place your thumb inside the anchor loop and your first two fingers around the trigger.
Squeeze fingers and thumb together till the trigger and spring fully compress.
5.
Insert unit at least 3” (76mm) deep into hole and release the trigger. Do not force.
6.
Set the unit with a slight tug on the anchor loop.
7.
The stop sleeve must always be partially inserted into the hole.
REMOVAL INSTRUCTIONS:
1.
When removing anchor, place your thumb inside the anchor loop
and your first two fingers around the trigger. Squeeze fingers and
thumb together until the trigger and spring fully compress.
2.
While squeezing the trigger, pull the anchor out of the hole.
3.
If the anchor becomes stuck, insert a punch, screwdriver or other
object into the hole until it touches the top of the cleaning bushing.
4.
Lightly tap with a hammer, making sure the tool is touching the top
of the cleaning bushing, while squeezing the trigger. The cleaning
bushing should be easily visible at the edge of the hole.
5.
If tool was required to remove the anchorage, inspect thoroughly
for damage after removal. If damage is found, remove from service
and destroy immediately.
Swage
*The user shall be equipped with
a means of limiting the maximum
dynamic forces exerted on the
user during the arrest of a fall to a
maximum of 8 kN (1800-lbf).
In the
EU these forces must be limited
to 6 kN (1350-lbf).
Compliance: OSHA 1926.502, OSHA 1910.66, ANSI Z359.1(07), ANSI Z359.7(11)
3/4”
Remo
vable
Concr
et
e A
nchor
M
odel: HWR
AF075N
Ba
tch# RB5-
XX
X
MFD: MM/Y
YY
Y
Stainless Steel, Aluminium, Zinc Plated Copper, 7x19 Aircraft Cable
Pat # 7,357,363 B2 / 7,011,281 B2 / US 6,729,821 B2
WARNING:
ALL PERSONS USING THIS EQUIPMENT MUST
READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO DO
SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS SHOULD
BE FAMILIAR WITH PERTINENT REGULATIONS GOVERNING THIS
EQUIPMENT. ALL INDIVIDUALS WHO USE THIS PRODUCT MUST
BE PROPERLY INSTRUCTED ON HOW TO USE THE DEVICE. AVOID
CONTACT WITH PHYSICAL HAZARDS (THERMAL, CHEMICAL,
ELECTRICAL, ETC.). MAKE ONLY COMPATIBLE CONNECTIONS.
(207) 282-2550
HOLE DRILLING REQUIREMENT CHART
(A)” Minimum distance from edge/corner (B)” Concrete thickness
6” (15.3 cm)
12” (30.5 cm)
12” (30.5 cm)
5” (12.7 cm)
PERFORMANCE:
Static Tensile Strength:
5000-lbf (22kN)
Maximum Capacity:
One worker with
max weight of 310-lbs when used as a
single point anchorage connector for
personal fall arrest or restraint system
DIMENSIONS:
Weight:
.44-lbs (200g)
Length:
11.5” (293mm)
Diameter
.75” (19mm)
REGULATORY COMPLIANCE:
ANSI Z359.1-2007, ANSI Z359.7-2011
OSHA 1926.502, OSHA 1910.66,
COMPONENT MATERIALS:
Aluminum:
Trigger
Aircraft Cable:
Main Cable, Activator Wire
Polyurethane:
Loop Cover
Stainless Steel:
Cone, Spoons, Stop Sleeve
Zinc Plated Steel:
Spring
Zinc Plated Copper:
Swage
90º
90º
0º
PROPER LOADING
Good
Best
See Spoon Orientation
Good
See Spoon Orientation
*Best practice for spoon orientation
when loaded 90º to hole.
SPOON ORIENTATION
Best
Ok
Load
Load
=
=