Steris P920011-649 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 168

background image

4-4

920011-649

Operator Manual

Processing Instructions

then:

then:

and printer records, for example:

===========================
PROGRAM = 117-XXX-XXX
REV. = XX MM-DD-YY
===========================
CONTROL ON HH:MM:SS XM

MM-DD-YY

===========================
Reliance
Endoscope
Processing
System
S/N 36XXXXXXXXX
===========================

NOTE:

If display shows D-SHORT REQUIRED XX HOURS

LEFT or D-SHORT REQUIRED XX MINUTES LEFT, refer to

6.5, D-SHORT C

. If display shows D-LONG

REQUIRED NOW, refer to

6.11, D-LONG C

2. Press

UNLOCK

toggle switch to unlock processor door. Open

door.

3. Manually rotate spray arms on chamber ceiling and under

endoscope processing support to ensure movement is not

obstructed. If spray arms do not rotate freely, refer to

ROUBLESHOOTING

4. Pull endoscope processing support out of chamber and onto

door.

5. Verify:

a. Chamber is empty and free of objects.
b. Removable debris screen at bottom of chamber is in place

and free of debris (refer to Figure 3-3).

6. Place accessories in Reliance EPS Processor (refer to

Endoscope Quick Reference Guide

for more details):

a. Place bite blocks on accessory pegs (see Figure 4-2).
b. Open accessory basket cover.
c. Place small items, such as air/water valves, in accessory

basket (see Figure 4-2, Detail A).

STERIS CORP

COPYRIGHT (C) 2011

READY

MM-DD-YY

HH:MM XM

WARNING – INEFFECTIVE

PROCESS HAZARD:

•

Follow

all

applicable

instructions  provided  by  the
endoscope manufacturer  for
preparing  endoscope  and
accessories for immersion.
Failure to do so may result
in damage to endoscope and/
or ineffective processing.

•

Before starting a cycle,

ensure rotary spray arms on
endoscope

processing

support and within chamber
are not obstructed and rotate
freely.  If  rotary  spray  arms
are  obstructed,  equipment
damage  may  result,  and
processor will be unable to
effectively process load.

WARNING – INEFFECTIVE

PROCESS  HAZARD:  To avoid
equipment  damage  and  help
ensure  processing  efficacy,
always follow directions when
loading  items  in  endoscope
processing support.

«
...
47
48
49
50
51
...
»

Содержание P920011-649









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P920011-649

Бренд: Raymarine Страницы: 90

Бренд: 3M Страницы: 48

Бренд: 3M Страницы: 19

Speedglas G5-01

Бренд: 3M Страницы: 62

Quickfit Nexus Exit

Бренд: Thomas & Betts Страницы: 2

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: Banfer Страницы: 6

Бренд: Baroness Страницы: 40

Бренд: Baroness Страницы: 40

Бренд: G-Systems Страницы: 60

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: Gary Machinery Страницы: 14

Бренд: IDEAL Networks Страницы: 60

Бренд: IceCure Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды