Steris AMSCO 400 Series Скачать руководство пользователя страница 53

Страница: 53 / 174

5-17

Component Identification

Operator Manual

P129394-020

5.10 Emergency Door

Opening Procedure

This procedure should only be used when pressure remains in the

sterilizer chamber, and the door cannot be opened normally
because the sterilizer has lost either electrical or water utilities.

•

Use emergency door opening procedure to retrieve a load
trapped in the chamber.

•

This procedure requires pushing on the door cover to retract the
door seal into the groove, then pushing the door

downward

manually.

Procedure:

Swing open the access panel of the sterilizer. Open the
emergency exhaust hand valve until chamber exhausts to
0.0 psig. See

Figure

5-13

Using the door release tool provided, press on the upper left
hand and right hand corners of the chamber door (see

Figure 5-13

). The door should give inward slightly, indicating that

the seal has been pushed into the groove. The door must
“bottom out” against the metal end-frame of the sterilizer
chamber.

Close the access panel of the sterilizer.

Press down on the door handle to lower the door. The door will
slide stiffly, so be prepared to press down hard.

Once the door is open, do not use the sterilizer until the unit has
been examined by a qualified service technician. Further use
without attention may damage the sterilizer.

Close the emergency exhaust valve.

Figure 5-13. Emergency Door Opening Procedure

WARNING – BURN HAZARD:
Do not attempt to open
sterilizer door if a water in
chamber alarm condition
exists.

Emergency Seal

Retract Tool

Emergency Exhaust

Valve

Содержание AMSCO 400 Series















































































































































































Результаты поиска

Содержание AMSCO 400 Series

Отзывы:

Бренды по названию

Популярные бренды

Steris AMSCO 400 Series, Руководство оператора

Результаты поиска

Содержание AMSCO 400 Series

Отзывы:

Бренды по названию

Популярные бренды