SteppIR MonstIR Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 46

SteppIR MonstIR Скачать руководство пользователя страница 32

SteppIR Antennas — MonstIR

32

Note:

If you ordered the 16 conductor control cable, it is included in your antenna kit. The

required 25 pin connector has been installed on one end and the factory has stripped
and tinned the wires on the other end. If you did not order this cable you must supply
your own 16 conductor cable and DB-25 pin connector. In such case, a separate
connector, back shell and cable wiring drawing have been included in your kit. Call
the factory if you would like to order a cable already prepared.

Now start at one end of the boom and tape all the cables snugly to the bottom of the boom so
there are no loops or slack cables. This is to prevent the cables from becoming damaged
when moving the antenna and installing it on your tower. Secure the 16 conductor cable and
coax to the boom about 8” from the coax connector. Refer to

Figure 5

for our

suggested

cable configuration.

Warning: Be sure to secure the cables before placing the antenna on the tower, as you

will not be able to reach the driven element from the tower !!!

Be careful

NOT

to tape the cables over a sharp edge unless you provide extra

protection to prevent eventually cutting through the sheath and shorting the
wires.

Note: If you do not want to install or remove the antenna with the main coax feed line at-

tached, make a coax jumper that connects to the driven element and goes along the
boom back to the mast plate area where it can be connected to the main coax feed
line coming up the tower.

Tape the cable every foot or so with electrical tape, we recommend taping it on the bottom
side to reduce exposure to UV. When going past an element bracket you can run the cable
between the bracket and the boom, it is much cleaner than routing it on the outside of the
bracket.

Warning: If you cut the element cables MAKE SURE you measure very carefully .

Carefully

review

Picture 25 & Figures 4

before proceeding. First complete the reflector,

director and driven element wiring then the 16 conductor cable going to the controller will
follow.

Starting with the driven element cable

dip each wire into the connector protector- except

the bare ground wire

(a thin coating is sufficient). Insert each of the four colored wire into

their respective location on the first 8 position terminal strip. Make sure you don’t insert the
wire so far in that you are clamping down on just the insulation.

Figures 4

provides the ex-

act location the color codes.

Figure 5

Secure Cable to Boom

Rotor Loop:
Control Cable & Coax
Taped Together

Suggested Cable

Routing

«
...
30
31
32
33
34
...
»

Содержание MonstIR















































Отзывы:

Нет отзывов