background image

Next, you will weatherproof and UV protect each joint with the black self-curing silicone tape see Fig-
ure 11
.  It is important that you pre-cut the silicone tape to the recommended lengths.  If you do 
so, you will have more than enough for each joint.  Refer to Figure 13 for proper lengths for each joint. 
In the event you require more silicone wrap, Home Depot electrical department carries Model HTP-
1010 Gardner Bender Silicone Rubber Fusion Tape, UPC code: 032076560102; and Radio Shack and 
Wall-Mart are authorized retailers for the brand we buy, Tommy Tape. 
 
 

IMPORTANT:    

Per the manufactures specifications the silicone tape has a shelf life of 12 

months before it is used and should be stored in a cool dry environment.  Silicone tape 
will not stick to just any surface.  It only bonds to itself.  Be sure to remove all the 
connector protector residue from your hands before handling silicone tape, as that 
residue will cause the silicone wrap not to adhere to itself in places.  Take care to keep 
the silicone wrap free of dirt or debris.  Also, this tape MUST be cut.  Do not tear it.  
Wash your hands before completing the following steps.  

 
 
Position the black silicone tape about 1/2” to the right of the black electrical tape and wrap one layer,  
continually stretching the silicone tape a minimum of 100 % its original length, completely around the 
pole so the tape fully overlaps itself.  Then slowly wrap the silicone tape to the left using half overlap 
wraps, extending about 1/2” beyond the black electrical tape.  When you reach the end, wrap one layer 
completely around the pole so the tape fully overlaps itself just as you did at the beginning of the wrap.  
If you are stretching the tape correctly you will get about two layers of tape at each joint.  As before, 
carefully stretch and lay the tape down as smooth as possible.  The final joint should look like Figure 
11
.  
 
Important:  After the silicone tape has been applied, be sure to rub each wrap with your hand 

several times to ensure that it is flat and has adhered to itself. 

SteppIR  Antennas - Dipole 

10  

 Recommended Lengths for Silicone Tape Wrapping

A

B

C

18 in / 46 cm

11 in / 28 cm

A  -

C  -

16 in / 41 cm

B  -

Figure 13

 

Содержание 80m Dipole

















Отзывы: