stellar labs Slider50, Руководство пользователя

Страница: 24 / 62

18 Slider50 Owner’s Manual
Stellar Slider50 Hydraulic Hooklift Specifications
54" H.H.(1372mm): Max. Lifting Capacity: 50,000lbs. (22,680kg), evenly distributed in, or on the body.
54" H.H.(1372mm): Max. Dumping Capacity: 50,000lbs. (22,680kg), evenly distributed in, or on the body.
Operating Pressure: 4,300psi (29.65Mpa)
61.75"(1568mm): Max. Lifting Capacity: 50,000lbs. (22,680kg) evenly distributed in, or on the body.
61.75"(1568mm): Max. Dumping Capacity: 50,000lbs. (22,680kg) evenly distributed in, or on the body.
Operating Pressure: 3,600psi (25Mpa)
Max. Dump Angle: 50 degrees.
Hook Height: Adjustable hook height to handle 54" (1372mm) or 61.75" (1568mm) hook height bodies.
Shiping Weight: Not to exceed 6,600lbs. (2,994kg.)
Hydraulic Gear Pump: Correctly sized direct-coupled piston type pump.
Hydraulic Control Valve: Correctly sized hydraulic valve mounted directly on top of oil reservoir.
Controls: Dual manual levers with sealed cable actuators mounted in the cab to allow full feathering of all hooklift functions.
Must also have center lock out to meet OSHA 1926.601(b)(11).
Sliding Jib Assembly: Hooklift must have sliding jib, to provide a low loading/unloading height of 179" (4,547mm), based on a 41"
(1,041mm) chassis frame height. Inner and outer jib booms must be hexangular shaped to reduce flexing, add to
structural integrity, and ease wear pad replacement. The sliding jib assembly must be able to hydraulically slide
the body/container horizontally without the use of wear pads for the body skid to slide on. Rollers will only be
accepted, no wear pads accepted.
Jib Cylinder: Single 5" (127mm) bore with 2.5" (66mm) diameter rod cylinder. Cylinder must be double acting and include dual
pilot operated counter-balance valves to prevent cylinder collapse in case of hose failure. Cylinder is sized for
rated capacity.
Jib/Dump Operation: Hooklift must include a hydraulic lock-out device to prevent operation of the sliding jib while in the dump mode.
LIFT/Dump Cylinders: Dual 7" (178mm) bore with 3" (64mm) diameter rod cylinder. Cylinders must be double acting and include dual
pilot operated counter-balance valves to prevent cylinder collapse in case of hose failure. Cylinders are sized for
rated capacity.
Jib/Dump Interlock: Dumping must be accomplished through a rear pivot. Jib and dump sections must lock together to support the full
length of the container/body. This must be accomplished without the use of springs, latches, hydraulic/air cylin-
ders, gravity, to change mode of operation. The dump/jib interlock should be accomplished by means of tabs on
jib boom which then slide under the dump to form support under the full length of the container and change the
pivot point for dumping to the rear of the hooklift.
Rear Body Hold-downs: Slide through hold-downs devices mounted on the dump section to secure the rear of body through out a wide
range of body lengths through the entire transportation and dump mode operation. Hooklift must be compatible
with containers manufactured to ANSI Z245.60 standards for waste containers.
Rear Hinge Pin: 3 1/2" diameter (89mm), type 17-4 stainless steel.
Pins: All pins to be made of 17-4 stainless steel.
Bushings: All bushings are to be a permanently lubricated and greaseable type.
Hoses and Fittings: All hoses and fittings are to SAE metrics are not allowed. O-ring face seal fittings are to be utilized
wherever possible.
Finish Paint Coating: Hooklift weldments must be finished painted with DuPont® Imron 5000 paint.
Orgin of Manufacturer: Hooklift must be designed and manufactured in the United States of America.