7
SLIP
SCOOP
ASSEMBLY INSTRUCTIONS
Refer to Pages 10 - 13 for Parts
Identification
Assembly Instructions 75-70625A
(Figure 1)
1. Unfasten the bucket (Fig. 1, Item 16) and the
sub-frame (Fig. 1, Item 15) from the sides of the
crate and remove.
2. Remove the hardware package from the crate
and open.
3. Loosen all ball joints prior to connecting them to
the bucket.
4. Place the bucket between the frame arms so that
the holes at the ends of the arms line up with the
lower set of holes on each side of the bucket.
5. Insert a 5/8 X 2-1/2 bolt (Fig. 1, Item 19) through
the rear end of each arm and place one 5/8 flat
washer (Fig. 1, Item 12) and one spacer (Fig. 1
Item 5) on each bolt. Insert the bolts through the
lower holes on each side of the bucket. Place a
5/8 stover locknut (Fig. 1, Item 18) on each bolt
and tighten.
6. Insert a 5/8 X 2-3/4 bolt (Fig. 1, Item 3) through
the rod end of each cylinder (Fig. 1, Item 4) Place
a washer (Fig. 1, Item 12), and two spacers (Fig.
1, Item 5) on each bolt. Insert the bolts through
the upper holes on each side of the bucket.
Place a 5/8 stover locknut (Fig. 1, Item 18) on
each bolt and tighten.
7.
If installing on a 430/440
or earlier tractor,
please locate the two loose couple hoses (Fig.
1, Item 7) and fittings (Fig. 1, Item 8) provided.
Remove fittings (Fig. 1, Item 21 & 22) and
existing hoses (Fig. 1, Item 20 & 23) from slip
scoop. Install hoses (Fig. 1, Item 7) and fittings
(Fig. 1, Item 8) the per illustration on page 10.
Insure hoses are clear from the wheels when
the scoop is raised and lowered. Adjust as
necessary.
Assembly Instructions 75-70630A
(Figure 2)
1. Unfasten the bucket (Fig. 2, Item 16) and the
sub-frame (Fig. 2, Item 15) from the sides of the
crate and remove.
2. Remove the hardware package from the crate
and open.
3. Loosen all ball joints prior to connecting them to
the bucket.
4. Place the bucket between the frame arms so that
the holes at the ends of the arms line up with the
lower set of holes on each side of the bucket.
5. Insert a 5/8 X 2-3/4 bolt (Fig. 2, Item 3) through
the lower hole on each side of the bucket.
(Through the outer bracket only.) Insert bolts
through the end of each arm and place one
washer (Fig. 2, Item 12) and two spacers (Fig. 2,
Item 5) on each bolt. Push the bolts through the
bucket. Place a 5/8 stover locknut (Fig. 2, Item
18) on each bolt and tighten.
6. Insert a 5/8 X 2-3/4 bolt (Fig. 2, Item 3) through
the upper hole on each side of the bucket.
(Through the outer bracket only.) Insert bolts
through the rod end of each cylinder
(Fig. 2, Item 4) and place one wahser (Fig. 2,
Item 12) and two spacers (Fig. 2, Item 5) on each
bolt. Push the bolts through the bucket. Place a
5/8 stover locknut (Fig. 2, Item 18) on each bolt
and tighten.
7.
If installing on a 430/440
or earlier tractor,
please locate the two loose couple hoses (Fig.
2, Item 7) and fittings (Fig. 2, Item 8) provided.
Remove fittings (Fig. 2, Item 17 & 24) and hoses
( Fig. 2, Item 19 & 25) from slip scoop. Install
hoses (Fig. 1, Item 7) and fittings (Fig. 2, Item 8)
the per illustration on page 12. Insure hoses are
clear from the wheels when the scoop is raised
and lowered. Adjust as necessary.
