STEINEL 032845, Инструкция по эксплуатации

Страница: 9 / 10

- 24 - - 25 -
7� Operation / maintenance
Weather conditions may affect the
way the motion detector works.
Strong gusts of wind, snow, rain or
hail may cause the light to come
ON when it is not wanted because
the sensor is unable to distinguish
between sudden changes of tem-
perature and sources of heat. The
detector lens may be cleaned with a
damp cloth if it gets dirty (do not use
cleaning agents).
8� Disposal
Electrical and electronic equipment,
accessories and packaging must
be recycled in an environmentally
compatible manner.
Do not dispose of electrical
and electronic equipment
as domestic waste.
EU countries only:
Under the current European Directive
on Waste Electrical and Electronic
Equipment and its implementation in
national law, electrical and electronic
equipment no longer suitable for
use must be collected separately
and recycled in an environmentally
compatible manner.
9� Manufacturer's warranty
This STEINEL product has been
manufactured with utmost care,
tested for proper operation and
safety and then subjected to random
sample inspection. Steinel guaran-
tees that it is in perfect condition
and proper working order. The war-
ranty period is 36 months and starts
Time setting (Fig� 6�3)
The time you wish the connected
light to stay ON for can be infinitely
adjusted from approx. 8 s to a maxi-
mum of 35 min.
Control dial position 1 is the
shortest time, approx. 8 s.
Control dial position 6
is the
longest time, approx. 35 s.
Note: It is recommended that the
shortest time be set when adjusting
the sensor for the detection zone
and performing a function test.
Twilight setting (Fig� 6�4)
The desired response threshold of
the detector can be infinitely varied
from approx. 2 - 2000 lux.
Position 1 is daylight operation,
approx. 2000 lux.
Position 6 is night-time operation,
approx. 2 lux.
• After making the function settings,
screw the sensor back in (clock-
wise) to return it to the home
position. (Fig� 6�5)
• Push the designer ring onto the
enclosure (Fig� 6�6)
Reach setting (Fig� 6�7 / 6�8)
The detection zone can be optimised
to suit requirements. The shrouds
supplied with the sensor can be used
to mask out as many lens segments
as you wish or shorten reach to suit
the particular situation. This prevents
the light from being activated unin-
tentionally, e.g. by cars, passers-by
etc. and allows you to target danger
spots. The shrouds can be separated
along the pre-grooved divisions in
the vertical and horizontal directions
or cut with scissors.
10� Technical specifications
Dimensions, Ø × H 78 × 89 mm
Minimum installation depth 54 mm less thickness of ceiling panel
Mains power supply 220-240 V, 50 / 60 Hz
Output
Incandescent / halogen lamp load
Fluorescent lamps, electronic ballast
Fluorescent lamps, uncorrected
Fluorescent lamps, series-corrected
Fluorescent lamps, parallel-corrected
Low-voltage halogen lamps
LED < 2 W
2 W < LED < 8 W
LED > 8 W
Capacitive load
1000 W
430 W
500 VA
406 VA
406 VA
1000 VA
16 W
64 W
64 W
132 μF
Sensor technology Passive infrared
Angle of coverage 360°
Reach max. 4 m
Time setting 8 s - 35 min
Twilight setting 2-2000 lux
IP rating IP54
Temperature range -20°C to +40°C
Service:
Our Customer Service Department
will repair faults not covered by
warranty or after the warranty period
has expired. Please send the product
well-packed to your nearest
Service Centre.
on the date of sale to the consum-
er. We will remedy defects caused
by material flaws or manufacturing
faults. The warranty will be met by
repair or replacement of defective
parts at our own discretion. The
warranty shall not cover damage
to wear parts, damage or defects
caused by improper treatment or
maintenance. Further consequential
damage to other objects shall be
excluded. Claims under the warranty
will only be accepted if the unit is
sent fully assembled and well-packed
with a brief description of the fault, a
receipt or invoice (date of purchase
and dealer's stamp) to the appro-
priate Service Centre.
MANUFACTURER'S
1 3
5
Y E A R
G B
WARRANTY
MANUFACTURER'S
Y E A R
WARRANTY
MANUFACTURER'S
Y E A R
WARRANTY