Instructions for use for the STEIN COPIOUS (ID RGK26EE)
complying with the requirements of EN795:1996 Class B. Read these instructions carefully before use.
Failure to follow these instructions may endanger life
Before use, a detailed risk assessment must be carried out by a competent person to establish that this is the correct product suitable for the type of
work to be being undertaken, taking into account anchor points, potential fall distance, obstructions, rescue system, etc.
The
Copious
is designed to be used as an anchor device tested to EN795:1996 Class B. It may not be used in a fall arrest system without energy absorbers according
to EN355. Maximum rated load assembled in accordance with these instructions is 100kg or a single user. All parts must be checked regularly before, during, and after
use. The length of the anchor device must be determined by the size of the object it is to be looped over or around. In order to avoid high loads the anchor point for
belay purposes must always be directly above the person to be belayed or suspended. Slack ropes must be avoided at all times.
Purchasers and users should seek professional training from a fully qualified and competent instructor prior to engaging in any activity using this equipment in the
following configuration. If you are not able, or not in a position to assume this responsibility, do not use this product. The manufacturer its distributors and retailers do
not accept any liability if users do not follow the instructions correctly. Only the techniques shown in the diagrams are authorised. Any other use deviating from those
shown may result in serious injury or death. Prior to each use a complete risk assessment must be carried out to ascertain that the device chosen configures with and
is appropriate to the work being undertaken.
(1)
Users are warned that certain medical conditions such as heart disease, high blood pressure, vertigo, epilepsy, drug or alcohol dependence, could affect the
safety of the user in normal and emergency use.
(2)
This equipment must only be used by suitably trained personnel who are competent in its safe use.
(3)
Ensure before use that there is a suitable rescue plan to enable the retrieval of the user to a place of safety in the event of a fall or injury
(4)
Never attempt to modify or repair this product.
(5)
The intended purpose of this product is to use as an anchor point. Never use for any other purpose other than that for which it is intended.
(6)
This product is recommended for personal issue.
(7)
Ensure that any safety lines used with this equipment are suitably CE approved and compatible with this product.
(8)
Also be aware of any possible dangers, which may arise through use of combinations of items of equipment in which the safe function of any one item is
affected by or interferes with the safe function of another.
(9)
Before use, the user must be suitably qualified to carry out a pre-use check (see section on inspection)
(10) It is essential for safety that the equipment is withdrawn from use immediately should:
·
any doubt arise about its condition for safe use or if the equipment shows excessive wear or damage to any part or
·
if it has been used to arrest a fall
(11) Ensure that all anchor points and devices are compatible with this equipment and they have a strength of at least 10kN.
(12) In order to reduce the potential fall distance, ensure that the equipment anchor point is as high as possible above the user.
(13) A full body harness is the only acceptable device that may be used to arrest a fall.
(14) Either the rear or front harness D ring are acceptable attachment points. Never use work positioning D rings as attachment points for fall arrest
(15) Ensure there is sufficient clearance below the user, so that in the event of a fall, there will be no collision with the ground or other obstacle in the fall path. In
particular, allow for elongation of energy absorbers.
(16) The RGK26/CS is suitable for use in normal atmospheric conditions (-20
°
C to +50
°
C).
(17) To prolong the life of the product it is essential to keep the product clean and away for dirt. Avoid impact, sharp edges or abrasive surfaces, contact with
strong acids or alkali, solvents, chemicals, excessive heat and/or sparks, UV exposure.
General Guide
0086
BS EN 795:1996 Class B
The CE on this product is only applicable when manufactured by Ridgegear.
Article 10 of PPE Directive. Satra Technology Centre, Kettering, Northampton NN16 9JH. ID number 0321.
Article 11 of PPE Directive. British Standards Institution, 389 Chiswick High Road, London W4 4AL ID number 0086.
Notified Body
STEIN is a registered Trade Mark of
Fletcher Stewart (Stockport) Limited
Product Identification
·
Ensure that a suitable anchor point is selected and is
compatible with the
Copious
. The anchor point must be able
to withstand the expected loads in worse case scenarios.
·
Even when using shock absorbers (according to EN355) the
anchor point should be able to withstand forces of at least
10kN.
·
Ensure there are no sharp edges or ridges. These should be
covered where necessary by auxiliary equipment.
·
Ensure the
Copious
is securely fixed to the anchor point and
it is not possible for the
Copious
to slide down a structure
such as a vertical beam (see connection to a rope below)
·
Always connect to the
Copious
with a compatible connector
meeting EN362 Standard (1)
·
The
Copious
can be shortened by wrapping it around the
anchor point (2)
·
NEVER use the
Copious
in a straight pull situation (3). It must
always be used in basket formation (1)
Standard Connection
1
2
Manufactured from Yale Cordage 10mm Silverstreak Cool Accessory Cord - 100% Polyester. Double Braid construction.
COPIOUS
Hot
Part Number: SS-1ESH075
Manufactured from Yale Cordage 10mm Silverstreak Hot Accessory Cord - 100% Polyester. Double Braid construction.
COPIOUS
Tec
Part Number: SS-1EBL075
Manufactured from Yale Cordage 10mm Beeline Accessory Cord - Cover contains 50% Technora / 50% Polyester. Inner core
contains 100% polyester. Kernmantle construction.
X
3
COPIOUS
Cool
Part Number: SS-1ESC075
COPIOUS
TAC
Part Number: SS-1EM0070
Manufactured from 8mm STEIN Globaltech Accessory Cord - Cover contains 50% Technora / 50% Polyester. Inner core contains
100% Polyurethane Coated SK75 Dyneema. Double Braid construction.
