V4E-2013 35mm New Line
18
6.2 WORKING WITH THE NEW LINE STEENBECK
Connect the Steenbeck to power as described in section 3.0 and 4.0.
Please take care that the power connector at the table is secured with the
safety clamping devise at the frame.
Always check if the power is according to the given voltage and frequency,
which can be found on the type and serial number plate at the back of the
frame.
Always check that the grounding of the power socket is correct.
Without a proper grounding, the operator might be at danger.
Use a free power group of at least 16 Amps.
Switch the power ON with the main power switch (16).
A part of the electronics of the table will go in standby and the fan will start
moving.
The push button 23 (standby) will show a RED light.
When the standby button (23) is pushed the light will turn to GREEN and the
table will start up in several stages in a short time.
Before switching OFF, it’s advised to always switch off the sub functions (27-
32-33-34-35) off first and then the Standby button 23. Finally the main power
switch 15 can be switched off.
After switching ON the processor the touch screen (TS) is activated too.
After a short time you will hear a ‘peep’ and the home page menu can be seen.
Now the table is ready for use and all the needed sub-functions can be chosen
now.
It’s advised to switch on only sub-functions which are needed.
The sound is also activated after switching on.
If you don’t need sound, then please always MUTE the master sound control.
( see section 6.3 ) If you intend to use one sound source, please take care that
other pre-amps are muted.
FILM THREADING.
Threading of the film is done as explained in fig. 29 – 30 - 31 .
The left hand sprocket has a spring, enabling the film ton be set with the
correct tension in combination with the right hand sprocket.
Always check the tension before running the table!! The film can get damaged!
When a film with optical sound has to be viewed threat the film as shown in
fig.29 .
Now push button 37 ( tension COMPOPT) and the tension roller 58 can be
disengaged.
Align the film now by pulling the film to the right giving a margin of at least
one perforation at the tension roller.
Keep the film at that spot and engage again with button 37.
Содержание ST3512
