SteelMax D1 AUTO Скачать руководство пользователя страница 6

Страница: 6 / 23

D1 Operator’s Manual

2. SAFETY PRECAUTIONS

1. Before starting

, read this Operator’s Manual and complete proper occupational

safety and health training.

2. Use the

machine only in applications specified in this Operator’s Manual.

3. The

machine

must

complete

and

all parts must be genuine and fully functional.

4. The specifications of the power source

must

conform

those

specified

the

rating

plate.

5. Connect the machine to a properly grounded power source. The power source must

be protected with a 16 A fuse for 230 V or a 32 A fuse for 115 V. When used on

building sites, supply the machine through an isolation transformer with class II

protection only.

6. Never carry the machine by the power cord and never pull the cord because this

may damage it and result in electric shock.

7. Transport

and

position

the

machine

using

the

carrying

handle

and

only

when the

MAGNET switch is set to ‘O’.

8. Untrained bystanders must not be present near the machine.

9. Before

starting,

ensure the correct condition of the machine, power source, power

cord, plug, control panel components, and cutters.

10. Keep the machine dry, and never expose it to rain, snow, or frost.

11. Never stay below the machine placed at heights.

12. Keep the work area well lit, clean, and free of obstacles.

13. Install the annular cutter securely by tightening the set screws. Remove wrenches

from the work area before connecting the machine to the power source.

14. Never use cutters that are dull or damaged.

15. Install and remove tools by using protective gloves and only when the machine is

unplugged from the power source.

16. Never use annular cutters without the pilot pin except when drilling incomplete

through holes.

17. Do not make holes which diameter or depth differ from those specified in the

technical data.

18. Never use near flammable liquids or gases, or in explosive environments.

19. Never use the machine on surfaces that are rusty, covered with paint, uneven, or

not rigid.

Содержание D1 AUTO
























Результаты поиска

Содержание D1 AUTO

Отзывы:

Похожие инструкции для D1 AUTO

Бренды по названию

Популярные бренды

SteelMax D1 AUTO, Руководство оператора

Результаты поиска

Содержание D1 AUTO

Отзывы:

Похожие инструкции для D1 AUTO

Бренды по названию

Популярные бренды