Steca coolcept StecaGrid 1500 Скачать руководство пользователя страница 5

Страница: 5 / 94

General information

2.1 General safety instructions

This document is part of the product.

Install and use the device only after reading and understanding

this document.

Always perform the measures described in this document in the

sequence specified.

Keep this document in a safe place for the entire service life of

the device. Pass the document on to subsequent owners and

operators of the device.

The yield of the system can be reduced through improper

operation

If the housing is damaged, do not connect the device to the DC

or AC lines

If one of the following components is damaged, immediately

take the device out of operation and disconnect it from the

mains grid and PV generators.:
–

Device (not functioning, visible damage, smoke,

penetration of liquid etc.)

–

Lines

–

PV generators

Do not switch the system on again before
–

the device has been repaired by a dealer or the

manufacturer,

–

Damaged cables or PV generators have been repaired by a

technical specialist.

Never cover the device

Do not open the casing: Risk of death. Invalidation of the

guarantee.

Factory labels and markings must never be altered, removed or

rendered unreadable.

Comply with the instructions of the respective manufacturer

when you connect an external component that is not described

in this document (e.g. external data loggers). Components that

are incorrectly connected can damage the device.

747,431 | Z09.2 | 18/02/2016

Содержание coolcept StecaGrid 1500































































































Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды

Steca coolcept StecaGrid 1500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание coolcept StecaGrid 1500

Отзывы:

Похожие инструкции для coolcept StecaGrid 1500

Бренды по названию

Популярные бренды