Note:
The factory set code is: 1 2 3 4 5 6 and should be changed before using the
safe. It is the owner’s responsibility to maintain the code.
Electronic Keypad:
1.
Use keypad to slowly enter 6-digit combination
(Factory set code is: 1 2 3 4 5 6)
*If there is one (1) long beep after entering the code, the code was not
recognized. Slow down and retry.
2.
Immediately rotate turning handle clockwise and pull open
Note:
There will be a 5 minute lockout penalty after 4 consecutive wrong code
attempts. If another 2 invalid codes are attempted, the safe will reenter lockout
mode and continue after every 2 invalid attempts until the correct combination
is entered.
• Close door and rotate turning knob counter-clockwise to relock bolts
• If bolts are deployed, reopen safe before closing
Changing Lock Combination:
1.
Unlock the safe door and leave it open and in the locked position so that the
bolts are visible (Factory set code is: 1 2 3 4 5 6)
2.
Press and hold ‘0’ until you hear a double beep. The LED light will remain on.
3.
Enter current 6-digit combination -- you will hear a double beep
(Factory set code is: 1 2 3 4 5 6)
5.
Enter new 6-digit combination -- you will hear a double beep
7.
Renter new 6-digit combination -- you will hear a double beep
8.
Your new combination is now installed
9.
Test your new combination with the safe door open to ensure that your new
code was installed correctly
Note:
If you hear one (1) long beep while entering your new combination, the
lock has timed out and your old combination is still valid. Enter old combination
once and then restart from Step 2.
USER'S INSTRUCTION MANUAL:
OPENING SAFE:
CLOSING SAFE:
CUSTOM PROGRAMMING SAFE:
DORM SAFE
US Patent D617974
Note:
In order to initially install battery, you must first remove keypad from safe
Installing Battery:
1.
Push keypad upward to disconnect from safe door
2.
Gently pull keypad away from safe
3.
Connect a brand new 9V battery to the battery connector
located on the back side of the keypad
4.
Insert connected battery into the battery compartment
5.
Reposition keypad and slide keypad down to lock into place
Replacing Battery:
Note:
If battery is low, lock will repeatedly beep while unlocking safe
1.
Unlock safe and leave door open and in locked
position so that bolts are visible
2.
Slide open battery compartment located beneath the keypad
3.
Battery should slide out from inside keypad
4.
Disconnect old battery and connect brand new 9V battery
5.
Insert battery back into compartment and slide closed
6.
Test keypad to ensure battery is connected properly
INSERTING AND CHANGING KEYPAD BATTERY:
• Keep liquids away from keypad
• Do NOT disassemble safe -- For all repairs call Stealth Customer Service
1.
Insert one end of steel cable through safe rear
access hole
2.
Wrap cable around a sturdy and secure object
next to safe
3.
Insert other end of steel cable into safe through
the other rear access hole
4.
Clasp each end of cable to hook
5. Clasp hook onto attachment hole connected to
bottom shelf to secure cable to safe
1.
Remove foam floor lining from inside of Dorm Safe
to reveal pre-drilled mounting holes
2.
Secure safe in desired location by screwing it into
place through the four (4) mounting holes and into
the floor using the screws provided
Note:
Screws provided are for wood or carpet
mounting only. Installation into concrete or tile
require the purchase of different hardware
-
Use proper drill tools depending on the type of
floor you are mounting the safe on (wood, tile, or
concrete)
-
Mark the exact locations of the mounting holes
on the floor where you want your safe to go
-
Drill the appropriate size holes for the
anchors you are using
-
Match the safe’s mounting holes over the drilled
holes in the floor
-
Insert the appropriate screws through the safe
and into the floor, then tighten until secured
3.
Reposition floor lining
4.
Your Dorm Safe is now securely mounted
SECURING SAFE WITH CABLE:
MOUNTING SAFE:
CARE AND MAINTENANCE:
Security Cable
Attachment Hole
(4) Pre-drilled Mounting Holes
