www.wildviewcam.com
Toll Free 877-269-8490
9
3.
Turn the camera to the ON position.
4.
The camera will automatically switch to external power when it is
connected, even if the internal batteries are installed.
NOTE: Please make sure the voltage and polarity (+/-) are correct before
connection. Incorrect voltage or polarity (+/-) will damage the camera.
When both internal and external batteries are connected, the camera
will draw power from the higher voltage source first.
Memory Options
The camera is also equipped with an expandable media card slot capable of
accepting up to 32GB SD card (sold separately). With no memory card
inserted into the slot, the camera will use the built in SDRAM memory to
store images. If an SD card is inserted into the slot, then the camera will
bypass the built in memory and utilize the SD memory. The front counter
display will show the number of images in the built in memory, unless the
expansion card is inserted at which point the front counter will only display
the number of images stored in the expansion card.
IMPORTANT SD CARD NOTICE
:
Wildview recommends that you use a
known good SD card from a reputable brand (including Stealth Cam memory
cards.) Beware of "low cost" memory cards often sold on discount websites such as
eBay as they could be manufactured to poor standards. Use of a low quality memory
card could result in camera lock up and / or shut down, video corruption issues or
premature battery drain.
www.wildviewcam.com
Toll Free 877-269-8490
10
Inserting SD memory card
NOTE: Make sure camera is in the OFF position whenever adding or
removing memory.
•
Insert SD memory card in to the SD card slot completely and in the
correct direction, as shown by the picture shown on the Inside View
image above (see page 5).
•
To remove the SD memory card, depress the SD card and pull out the
card gently.
•
SD cards must be clean (no images from other sources). If you are using
the SD card from other cameras, please make sure to format the SD card
in your computer prior to use in the camera. New cards are good to use
straight from the package.
•
If installed SD card is locked, camera will show LOC on the display, please
slide the lock switch to unlock location then reinstall the SD card.
FORMAT – Definition:
When you format a SD memory card, the operating
system erases all information and files on the card. Then it creates an internal
address tables that it later uses to locate information and files. Formatting
also removes all Hidden System files as well. Basically it cleans your SD
memory card just like if it was brand new. Please make sure to follow the
guidelines listed below:
SD Card size: 2GB or below, format using File System type
“
FAT
”.
SD Card size: 4GB or above, format using File System type
“
FAT32”
.
*DO NOT use File System type
“NTFS”
or
“exFAT”
, these formats are not
supported.
www.wildviewcam.com
Toll Free 877-269-8490
11
SETUP AND PROGRAMMING
Definitions
•
Cam:
To set which mode you want the camera to be in.
TEST = Test mode
OFF = Power Off mode
ON = Active Passive Infrared mode / Power On mode
•
Time out:
To set the amount of time the camera will sleep between PIR
triggering.
20s = 20 Seconds
1m = 1 minute
5m = 5 minutes
10m = 10 minutes
•
Resolution:
The resolution selection that you have chosen.
HI (High) = 6.0 Megapixels (Image interpolated from 5M sensor)
LO (Low) = 3.0 Megapixels
•
Burst
: To set the number of pictures or video length the camera will take
per PIR triggering.
1P = Single still image captured per PIR triggering.
3P = Three continuous still images captured per PIR triggering.
6P = Six continuous still images captured per PIR triggering.
VIDEO = Places camera in Video mode and will capture video per
setting above.
www.wildviewcam.com
Toll Free 877-269-8490
12
•
Video
: Sets the length of time how long you want to capture video.
15s = 15 seconds
30s = 30 seconds
60s = 60 seconds
•
PIR / TLM:
This allows you switch between PIR or a preset Time Lapse
Mode
PIR mode – Cameras is activated by passive infrared Sensor
TLM – Cameras is in preset Time Lapse Mode: Preset Values
Resolution: Hi (6.0 MP)
Time out is: 120 seconds
Burst mode: 1P
Starting time: 07:00AM
Ending time: 07:00PM
•
Date and Time:
Displays the date and time that you’ve set, on all still
images and video. (Using Quick Time Player or Window Media Player).
•
Moon phase:
Displays the moon phase. (Using Quick Time Player or
Window Media Player).
•
FULL:
When the external memory capacity reaches full, the front LCD
screen will show “FULL.”
