stayer AGR 2000 Скачать руководство пользователя страница 24

Страница: 24 / 80

When operating the machine with power from mobile

generators that do not have sufficient reserve capacity

or are not equipped with suitable voltage control with

starting current amplification, loss of performance

or untypical behavior can occur upon switching on.

Please observe the suitability of the power generator

being used, particularly with regard to the mains

voltage and frequency.

ILLUSTRATED DESCRIPTION

1 Release lever for protection guard
2 Spindle lock button
3 On/Off switch
4 Auxiliary handle
5 Grinder spindle
6 Protection guard for sanding
7 Mounting flange
8 Grinding/cutting disc (not included)*
9 Clamping nut
10 Revolving handle - 3 position*
*Accessories shown or described are not part of the

standard delivery scope of the product. A complete

overview of accessories can be found in our

accessories program.

3_OPERATING INSTRUCTIONS

PLACEMENT AND TESTING

To start the power tool, push the On/Off switch 3

forwards.
To lock the On/Off switch 3, press the On/Off switch 3

down at the front until it latches.
To switch off the power tool, release the On/Off switch

3 or, if it is locked, briefly push down the back of the

On/Of switch 3 and then release it.

Check grinding tools before using. The grinding

tool must be mounted properly and be able to

move freely. Carry out a test run for at least one

minute with no load. Do not use damaged, out-of-

centre or vibrating grinding tools. Damaged grin-

ding tools can burst and cause injuries.

TOOL CHANGE

Before any work on the machine itself, pull the

mains plug.
Grinding and cutting discs become very hot while

working; do not touch until they have cooled.

- Clean the grinder spindle 5 and all parts to be

mounted.
- For clamping and loosening the grinding tools, lock

the grinder spindle with the spindle lock button 2.

Actuate the spindle lock button only when the

grinder spindle is at a standstill.

Otherwise, the machine may become damaged.

Grinding Disc

Pay attention to the dimensions of the grinding tools.

The mounting hole diameter must fit the mounting

flange without play 7. Do not use reducers or adapters.
When using diamond cutting discs, pay attention that

the direction-of-rotation arrow on the diamond cutting

disc and the direction of rotation of the machine (see

direction-ofrotation arrow on the machine head) agree.
See graphics page for the mounting sequence.
To fasten the grinding/cutting disc 8, screw on the

clamping nut 9 and tighten with the twohole spanner.

After mounting the grinding tool and before swit-

ching on, check that the grinding tool is correctly

mounted and that it can turn freely. Make sure that

the grinding tool does not graze against the pro-

tection guard or other parts.

Dust/Chip Extraction

Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful

to one’s health. Touching or breathing-in the dusts

can cause allergic reactions and/or lead to respiratory

infections of the user or bystanders.
Certain dusts, such as oak or beech dust, are

considered as carcinogenic, especially in connection

with woodtreatment additives (chromate, wood

preservative). Materials containing asbestos may only

be worked by specialists.
– Use dust extraction whenever possible.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filterclass respirator.

Observe the relevant regulations in your country

for the materials to be worked.

LIMITS ON THE SIZE OF WORKPIECE

Approved Grinding Tools

All grinding tools mentioned in these operating

instructions can be used. The permissible speed [rpm]

or the circumferential speed [m/s] of the grinding tools

used must at least match the values given in the table.
Therefore, observe the permissible

rotational/

circumferential speed

on the label of the grinding

tool.