12
13
EN
EN
PREFACE
LANDING GEAR INSTALLATION
Mount the landing gears to both side of fuselage using six M2.5x10mm. Pay attentin to the marks
“L” & “R” on the bottom of the landing gears. The “L” landing gear should be mounted in left side
of fuselage; The “R” landing gear should be mounted in right side of fuselage.
01
02
HORIZONTAL STABILIZER INSTALLATION
Fit the horizontal stabilizer onto the fin. Then lock it with M3.0x16mm screw. Guide the pushrod
into the screw-lock connector on elevator horn, and lock it to avoid loosening.
Attach the fin tip onto its foundation on the top of fin as illustration.
Slide the fin tip to the end to avoid loosening.
03
04
05
06
Gratulation for your SEAWIND by Staufenbiel.
We are aware of, that there are plenty different ways of buliding up or setting up a model. These
Manual is just a sample of how you can build it.
Please read this manual carefully before start assembling the modell.
SET CONTENT
NEEDED TOOLS AND EqUIPMENT
www.sheng-teng.com
1
INTRODUCTION
Before starting to build, inspect the parts to make sure they are of acceptable quality. If any parts are missing
are not of acceptable quality, or if you need assistance with assembly, contact Product Support. When reporting
defective or missing part, use the part names exactly as they are written in the Kit Contents List.
01. Fuselage
02. Left Wing
03. Right Wing
04. Horizontal Stabilizer
05. Fin Tip
06. Propeller
07. Propeller Adapter
08. Spinner
09. Carbon Rod
10. Left Landing Gear
11. Right Landing Gear
..........................................................x1
..........................................................x1
........................................................x1
..........................................x1
..............................................................x1
..........................................................x1
..............................................x1
.................... ........................................x2
......................................................x1
..............................................x1
............................................x1
12. Screw (M2.5x14)
13. Screw (M3.0x16)
14. Screw (M2.5x10)
15. Battery Pack
16. “Y” Servo Extension
17. Charger
18. Transmitter
19. Decals
20. Instruction
21. Sucking Bottle
...............................................x1
...............................................x1
...............................................x6
.....................................................x1
...........................................x2
............................................................x1
.......................................................x1
.............................................................x1
............................................... .........x1
..................................................x1
Order NO. Description
ST 141 40AMP U-BEC ESC
ST 112 11.1V Lipo 2200mAh Battery
ST 172 ST6DF 2.4Ghz 6CH Transmitter
ST 180 ST6DF 2.4Ghz 6CH Receiver
ST 204 11x8 Propeller
ST 121 9g Servo
ST 122 17g Servo (P)
ST 124 36g Servo
Order NO. Description
ST 185 Servo Speed Reducer (SSR)
ST 160 3S Lipo Smart Balancing Charger
STSE 010 Fuselage Set
STSE 020 Wing Set
STSE 030 Staibilizer
STSE 040 Tip Fin
STSE 050 Landing Gear (L&R)
STSE 011 Brushless Motor
Replacement Parts List
Replacement part for the ST MODEL SeaWind are available using the numbers in the Replacement Parts List
that follows.
TOOLS REQUIRED
Sharp Hobby Knife
Needle Nose Pliers
Hex Wrench
Ruler
Awl
Flathead Screwdrivers (size:M,S)
≥
85mm
www.sheng-teng.com
1
INTRODUCTION
Before starting to build, inspect the parts to make sure they are of acceptable quality. If any parts are missing
are not of acceptable quality, or if you need assistance with assembly, contact Product Support. When reporting
defective or missing part, use the part names exactly as they are written in the Kit Contents List.
01. Fuselage
02. Left Wing
03. Right Wing
04. Horizontal Stabilizer
05. Fin Tip
06. Propeller
07. Propeller Adapter
08. Spinner
09. Carbon Rod
10. Left Landing Gear
11. Right Landing Gear
..........................................................x1
..........................................................x1
........................................................x1
..........................................x1
..............................................................x1
..........................................................x1
..............................................x1
.................... ........................................x2
......................................................x1
..............................................x1
............................................x1
12. Screw (M2.5x14)
13. Screw (M3.0x16)
14. Screw (M2.5x10)
15. Battery Pack
16. “Y” Servo Extension
17. Charger
18. Transmitter
19. Decals
20. Instruction
21. Sucking Bottle
...............................................x1
...............................................x1
...............................................x6
.....................................................x1
...........................................x2
............................................................x1
.......................................................x1
.............................................................x1
............................................... .........x1
..................................................x1
Order NO. Description
ST 141 40AMP U-BEC ESC
ST 112 11.1V Lipo 2200mAh Battery
ST 172 ST6DF 2.4Ghz 6CH Transmitter
ST 180 ST6DF 2.4Ghz 6CH Receiver
ST 204 11x8 Propeller
ST 121 9g Servo
ST 122 17g Servo (P)
ST 124 36g Servo
Order NO. Description
ST 185 Servo Speed Reducer (SSR)
ST 160 3S Lipo Smart Balancing Charger
STSE 010 Fuselage Set
STSE 020 Wing Set
STSE 030 Staibilizer
STSE 040 Tip Fin
STSE 050 Landing Gear (L&R)
STSE 011 Brushless Motor
Replacement Parts List
Replacement part for the ST MODEL SeaWind are available using the numbers in the Replacement Parts List
that follows.
TOOLS REQUIRED
Sharp Hobby Knife
Needle Nose Pliers
Hex Wrench
Ruler
Awl
Flathead Screwdrivers (size:M,S)
≥
85mm
Attention: Pictured transmitter, battery and charger are not included!
