State Water Heaters PRV 30 NORS G Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 28

background image

2

Read these installation instructions first before installing the appliance. Carefully read
the user instructions before igniting the appliance. Failure to follow these instructions
may lead to risk of explosion and/or fire and could cause material damage and/or bodily
harm.
Installation and commissioning should be carried out by a qualified competent installer.
The type of gas and the value at which the appliance is set standard in the factory are
registered on the rating plate. The appliance may only be installed in a room if this room
meets the ventilation requirements.

STATE WATER HEATERS accepts no responsibility for warranty, service and/or
product liability in case of unauthorized alterations, product modifications or
repair.

«
1
2
3
4
...
»

Содержание PRV 30 NORS G





























Отзывы:

Нет отзывов

Похожие инструкции для PRV 30 NORS G

Бренд: Wacker Neuson Страницы: 162

Бренд: Napoleon Страницы: 20

Бренд: Napoleon Страницы: 40

TriScroll 300 Series

Бренд: Varian Страницы: 19

Бренд: AMICUS Страницы: 12

Бренд: Napoleon Страницы: 32

Point-of-Use Drinking Water System

Бренд: R-Can Страницы: 12

Бренд: DCG Страницы: 12

Бренд: SKF Страницы: 32

Бренд: Mallory Страницы: 4

Бренд: T.I.P. Страницы: 120

Бренд: Gude Страницы: 40

Бренд: Ballu Страницы: 11

PowerFLO 7800 Series

Бренд: Delavan Страницы: 2

Бренд: VEAB Страницы: 14

Actun OPTI-QS Series

Бренд: Wilo Страницы: 364

Бренд: Dimplex Страницы: 20

Бренд: Easylife Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды