manualshive.com logo in svg

State Water Heaters Power Direct Vented Gas models, Инструкция по эксплуатации

Поделиться
Скачать
State Water Heaters Power Direct Vented Gas models Скачать руководство пользователя страница 34

34

resIdentIal Gas warrantY 

This warranty shall apply only when the heater is:

•  owned by the original purchaser;

•  installed for indoor operation only;

•  used  at  temperatures  not  exceeding  the  maximum 

 

  calibrated setting of its thermostat;

•  used  at  water  pressure  not  exceeding  the  working 

 

  pressure shown on the heater;

•  filled with potable water, free to circulate at all times and 

 

  with the tank free of damaging water sediment or scale 

 

  deposits;

•  used  in  a  non-corrosive  and  non-contaminated 

 

  atmosphere;

•  used with factory approved anode(s) installed;

•  in its original installation location;

•  in  the  United  States,  its  territories  or  possessions,  and 

 

  Canada;

•  sized  in  accordance  with  proper  sizing  techniques  for 

 

  residential water heaters;

•  bearing a rating plate which has not been altered, defaced 

 

  or removed except as required by the warrantor;

•  used  in  an  open  system  or  in  a  closed  system  with  a 

 

  properly sized and installed thermal expansion tank;

•  operated with properly installed drip leg in the gas supply 

 

  line;

•  fired with the fuel for which it was factory built;

•  fired at the factory rated input;

•  operated  with  the  inner  and  outer  combustion  chamber 

 

  doors  in  place  and  all  factory  seals  to  combustion 

 

  chamber intact.

•  installed  with  no  attempted,  nor  actual  modification  or

 

  alteration  of  the  water  heater’s  design  in  any  way,

 

   including  but  not  limited  to,  the  attachment  of  non-

 

  company approved appliances or equipment.

Any accident to the water heater or any part thereof (including 

freezing,  fire,  floods,  or  lightning),  any  misuse,  abuse  or 

alteration  of  it,  any  operation  of  it  in  a  modified  form,  any 

operation  of  the  water  heater  on  desalinated  (deionized) 

water,  or  any  damage  caused  by  attempts  to  repair  tank 

leaks  or  parts,  will  void  this  warranty.   This  warranty  does 

not cover water heaters replaced for cosmetic reasons or for 

reasons of noise, taste, odor, discolored and/or rusty water.  

This warranty does not apply to water heaters used to heat 

pools, whirlpools or hot tubs or used for space heating where 

its sizing does not conform with specifications of the heating 

component manufacturer.

This  warranty  gives  you  specific  legal  rights,  and  you  may 

have other rights which vary under the laws of each province. 

If any provision of this warranty is prohibited or invalid under 

applicable province law, that provision shall be ineffective to 

the extent of the prohibition or invalidity without invalidating 

the remainder of the affected provision or the other provisions 

of this warranty. 

THIS  WARRANTY  IS APPLICABLE  TO  THE  ORIGINAL 

OWNER ONLY, in accordance with the warranty terms and 

conditions specified below.

State Water Heaters (the warrantor) will furnish the ORIGINAL 

OWNER,  1) a replacement State water heater of equivalent 

size  and  current  model  if  the  glass-lined  tank  in  this  water 

heater leaks and,  2) a replacement part for any component 

part which fails. 

THE STATE WATER HEATERS REPLACEMENT MODEL OR 

PART WILL BE WARRANTED FOR ONLY THE UNEXPIRED 

PORTION OF THE ORIGINAL WARRANTY.  The warranty 

period will be determined by the original date of purchase of the 

water heater, or in the absence of a Bill of Sale verifying said 

date, from the date of manufacture indicated on rating plate 

affixed to this water heater.  This warranty is not transferrable 

and applies to models listed below:

When the water heater has been used for other than 

single 

family residential application;  

1.  The tank warranty shall be reduced to 1 year for 6 year

 

  models.  

2.   The  parts  warranty  shall  be  reduced  to  1  year  for  all

  

  models. 

condItIons and eXceptIons

This  warranty  shall  apply  only  when  the  water  heater  is 

installed  and  operated  in  accordance  with  1)  all  local  fire 

codes and plumbing codes, ordinances and regulations, 2) 

the  printed  instructions  provided  with  it,  3)  good  industry 

practices,  and  4)  proper  safety  practices  such  as  but  not 

limited to a properly sized drain pan if installed in an area 

where leakage from the tank or its connections would result 

in damage to the area adjacent to the heater.  In addition, a 

new temperature and pressure relief valve, certified by the 

Canadian Gas Association must have been properly installed 

and piped to the nearest drain.

 

serIes 

tank 

parts

 
  select 6-Year Models 

6-year 

6-year

 

Gs6

Содержание Power Direct Vented Gas models





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды