FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (A)/NMB-3(A)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to
.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or
agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits,
loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the
product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the
limitations or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください
。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
DIN Rail Mounting
1. Align the holes in the
DIN Rail Bracket
with the holes in the back of the
PoE
Splitter
.
2. Insert three
Phillips Head Screws
through the
DIN Rail Bracket
and into the
PoE
Splitter.
3. Tighten the
Phillips Head Screws
using a
Phillips Head Screwdriver
.
4. Hang the top of the
DIN Rail Bracket
(the section with the two metal clips) onto a
Top Hat
style
DIN Rail
.
5. Press the
DIN Rail Bracket
down and forward to lock the bottom section onto the
DIN Rail
.
2. Connect a
Network Cable
to the
Data Port
on the
PoE Splitter
and to the
Network
Port
on the
Non-PoE Equipment
.
Powering the Non-PoE Equipment
Connecting and installing the
Terminal Block
must be completed by a licensed
Electrician.
Notes:
Make sure that you turn off the
Power Source
before connecting the
Power
Wire
to the
Terminal Block
.
Do not exceed the recommend voltage as it may result in personal or product damage.
Connect the
Power Wires
from a
DC Power Source (44 - 57V DC)
to the
Terminal
Block Connectors
on the
Switch
. The terminals are marked on the exterior of the
Switch
(connect the
Positive Wire
to
V+
and the
Negative Wire
to
V-
).
• Secure the
Wires
by tightening the
Screws
in the
Terminal Block
with a
Flat Head
Screwdriver
Mounting the PoE Splitter
Wall Mounting
1. Align the holes in the
Wall Mount Brackets
with the holes in the back of the
PoE
Splitter
.
2. Insert two
Phillips Head Screws
through each
Wall Mount Bracket
and into the
PoE
Splitter.
3. Tighten the
Phillips Head Screws
using a
Phillips Head Screwdriver
(sold
separately).
4. Insert two
Screws
(sold separately) through the
Wall Mount Brackets
and into the
Mounting Surface
.
5. Tighten the
Screws
using the appropriate
Screwdriver
.
