FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 0.5cm
between the radiator and your body.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a three year warranty.
For further information on product warranty terms and conditions, please refer to
www.startech.com/warranty
.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください
。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
2. Connect the other end of the
HDMI Cable
to an
HDMI In Port
on a
Video Display
Device
.
RJ45 Port
The
RJ45 Port
is used to connect the
Multiport Adapter
to a
Network Device
.
1. Connect a
CAT5e/CAT6 Cable
to the
RJ45 Port
on the
Multiport Adapter
.
2. Connect the other end of the
CAT5e/CAT6 cable
to an
RJ45 Port
on a compatible
Network Device
.
VGA Port
The
VGA Port
is used to connect the
Multiport Adapter
to a
Video Display Device
.
1. Connect a
VGA Cable
to the
VGA Port
on the
Multiport Adapter
.
2. Connect the other end of the
VGA Cable
to the
VGA Port
on a
Video Display
Device
and tighten the two screws of either side on the
VGA Connector
.
3. Depending on the
Host Computer’s
operating system, the
Multiport Adapter
will
automatically detect and install the required driver.
Connecting the Multiport Adapter
USB-A Port
The
USB-A Port
can be used as a charging port (e.g. cell phone, laptop, tablet, etc.), or to
connect a USB storage device (e.g. flash drive) or a USB peripheral device (e.g. keyboard,
mouse, etc.).
If connecting a
USB-A Device
that has a cable (e.g. cell phone):
1. Connect the
USB-A Device’s USB-A Cable
to the
USB-A Port
on the
Multiport
Adapter
.
2. Connect the other end of the
USB-A Cable
to a
USB Port
on your
USB Device
.
If connecting a
USB-A Device
with no cable (e.g. flash drive):
• Connect the
USB-A Device
to the
USB-A Port
on the
Multiport Adapter
.
If connecting a
USB-A Device
that has a built-in cable (e.g. mouse):
• Connect the
USB-A Device’s USB-A Cable
to the
USB-A Port
on the
Multiport
Adapter
.
HDMI Port
The
HDMI Port
is used to connect the
Multiport Adapter
to a
Video Display Device
.
1. Connect an
HDMI Cable
to the
HDMI Port
on the
Multiport Adapter
.
