background image

21

Manufacturer warrants, to the purchaser and 

subsequent owner during the warranty period, 

every new product to be free from defects in 

material and workmanship under normal use and 

service, when properly used and maintained, 

for a period of one year from date of purchase 

by the end user, or 18 months from date of 

original manufacture of the product, whichever 

comes first.  Parts that fail within the warranty 

period, one year from date of purchase by the 

end user, or 18 months from the date of original 

manufacture of the product, whichever comes 

first, that inspections determine to be defective 

in material or workmanship, will be repaired, 

replaced or remanufactured at Manufacturer’s 

option, provided however, that by so doing we will 

not be obligated to replace an entire assembly, 

the entire mechanism or the complete unit.  No 

allowance will be made for shipping charges, 

damages, labor or other charges that may occur 

due to product failure, repair or replacement.

This warranty does not apply to and there shall 

be no warranty for any material or product 

that has been disassembled without prior 

approval of Manufacturer, subjected to misuse, 

misapplication, neglect, alteration, accident or 

act of God; that has not been installed, operated 

or maintained in accordance with Manufacturer’s 

installation instructions; that has been exposed 

to outside substances including but not limited 

to the following:  sand, gravel, cement, mud, 

tar, hydrocarbons, hydrocarbon derivatives (oil, 

gasoline, solvents, etc.), or other abrasive or 

corrosive substances, wash towels or feminine 

sanitary products, etc. in all pumping applications.  

The warranty set out in the paragraph above is in 

lieu of all other warranties expressed or implied; 

and we do not authorize any representative or 

other person to assume for us any other liability 

in connection with our products.

Contact Manufacturer at, 95 North Oak Street, 

Kendallville, IN 46755, Attention: Customer 

Service Department to obtain any needed repair 

or replacement of part(s) or additional information 

pertaining to our warranty.

MANUFACTURER EXPRESSLY DISCLAIMS 

LIABILITY FOR SPECIAL, CONSEQUENTIAL 

OR INCIDENTAL DAMAGES OR BREACH 

OF EXPRESSED OR IMPLIED WARRANTY; 

AND ANY IMPLIED WARRANTY OF FITNESS 

FOR A PARTICULAR PURPOSE AND OF 

MERCHANTABILITY SHALL BE LIMITED 

TO THE DURATION OF THE EXPRESSED 

WARRANTY.

Some states do not allow limitations on the 

duration of an implied warranty, so the above 

limitation may not apply to you. Some states do 

not allow the exclusion or limitation of incidental 

or consequential damages, so the above 

limitation or exclusion may not apply to you.

This warranty gives you specific legal rights and 

you may also have other rights which vary from 

state to state.

WARRANTY

In those instances where damages are incurred as a result of an alleged pump failure, the 

Homeowner must retain possession of the pump for investigation purposes.

Содержание PowerFlush Optima S1201























Отзывы: