background image

 
 
 

 

 

Preventative Maintenance 

 

 

Katakana (KATA). 

 

 
 
MAINTENANCE  MODE 

Your  Service  Representative  may  need  to  check  accumulated  data  about  the  past  usage  of  your  Star 
Trac  E-SM  StairMill,  test  its  display  controls,  or  investigate  error  messages.  For  these  reasons,  your 
Stepper  is  equipped  with  a  Maintenance  Mode. The Maintenance  Mode  includes  all  of  the  items  available 
through Manager Mode, plus additional items for Service and Diagnostic use. To enter Maintenance Mode: 

 

1. 

Press and hold the 

,        and    keys together. 

2. 

A beep will sound and “MAINTENANCE MODE” will display momentarily in the Information Window. 

 

3. 

Release all keys. “SERIAL NO #####” will display in the 

Information Window. The following keys are available in 

MAINTENANCE MODE: 

 

Upper  and  Lower  Data Information Window  SCROLL   Keys:  Display the next and 

previous parameters, respectively. Keys will repeat if held. 

 

 

Increase  and Decrease LEVEL  Keys:  Adjust the value of the displayed parameter up and 

down, respectively, in incre- ments of 1 unit. These keys do not save the new value - see OK 

Key  below. 

 

 

Numeric  Keypad:  Allows you to enter specific values for numeric parameters. These keys do 

not save the new value 

- see OK Key  below. 

 

OK Key:  Updates (saves) the values of all parameters in non-volatile memory, and 

exits Maintenance Mode. NOTE: To exit Maintenance Mode without saving any values or settings, 

press the QUICK  START  key. 

 

 
 
 
 
 
 
 
 
 
 
 
 

Содержание E-SM






Отзывы: