Star Micronics DP8340RC Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 40

Star Micronics DP8340RC Series Скачать руководство пользователя страница 17

– 13 –

5. CONTROL CODES

CODE

LF
(0A)

H

FUNCTION

Print and line feed instruction

OUTLINE

The LF code causes the data in the line buffer to be printed,
followed by a single line feed. When the line buffer is empty,
only the feed takes place.

CODE

CR
(0D)

H

FUNCTION

Print and line feed instruction

OUTLINE

Same function as of LF code.
However, when the DIP switch 3 is ON, the CR code be-
comes invalid.

CODE

SO
(0E)

H

FUNCTION

Expanded character instruction

OUTLINE

This code causes the printer to print expanded characters
twice as wide as the regular ones. This remains in effect until
a DC4 code is received.

CODE

DC4
(14)

H

FUNCTION

Release from expanded characters

OUTLINE

The expanded character instruction is released by the DC4
code, and the succeeding data is printed as regular width
characters.

CODE

ESC-1
(1B)

H

(2D)

H

(01)

H

or (1B)

H

(2D)

H

(31)

H

FUNCTION

Underline mode selection

OUTLINE

All data received after this code is underlined until a ESC-0
is received.

CODE

ESC-0
(1B)

H

(2D)

H

(00)

H

or (1B)

H

(2D)

H

(30)

H

FUNCTION

Release from underline mode

OUTLINE

The underline mode selection is released by this code.

«
...
15
16
17
18
19
...
»

Содержание DP8340RC Series









































Отзывы:

Нет отзывов