-3-
RESET TO DEFAULT SETTINGS
To reset all settings to the factory defaults, proceed as follows:
•
Connect the BLACK wire to Ground.
•
Connect the WHITE wire and any
ONE
of the Enable wires to Power.
•
Connect the GREEN wire to Ground and the light will illuminate in a Steady Burn
mode. Keep the GREEN wire connected or 9 seconds and release it when the light
flashes 3 times.
•
Disconnect the WHITE wire from Power 1 second later.
† -
SAE approved patterns when properly
configured
Shortcuts - Hold GREEN wire to Ground for length
of time shown
Pattern Programming
With one of the colors activated, touch and
release the GREEN wire to GROUND to scroll
through the patterns to the right (or hold it to
advance directly to the shortcuts).
Phase 1 / Phase 2
All lights are shipped with both Enables (colors)
set for Phase 1. If you are synchronizing this light
with another and want the same color on the two
lights to alternate, while one color is activated,
use the shortcut shown in the
Standard
Programming Chart
(previous page)
to set the
corresponding color on the second light for
Phase 2.
(See Synchronization section for details)
Note:
When both colors are activated on one
light, Color 1 will always be forced into
the opposite Phase of Color 2.
Full Steady or Cruise Mode
If you want either color to be
Full Steady Burn
or
Cruise Mode
(low intensity Steady Burn
mode), activate that and use the shortcut shown in the
Standard Programming Chart
(previous page)
to set the corresponding Enable wire for the corresponding mode.
Exit either mode by holding the GREEN wire to ground for 3 seconds/1 blink.
PATTERN PROGRAMMING
ADVANCED PROGRAMMING
Priority
By default, Color 2 (YELLOW w/BLACK wire) is set for high priority. And functions as follows
•
Both Enables set for
Flashing
:
Both colors will flash in the pattern of Color 2. Additionally, Color 1 will automatically
flash in the opposite Phase of Color 2.
•
One or both Enables set for
Steady
:
Only Color 2 will activate. Color 1 will de-activate.
If you would like to change the priority of the colors, so that Color 1 overrides Color 2,
proceed below:
1. Connect the BLACK wire to Ground.
2. Connect Power to the WHITE wire and Enable 1 (i.e. the color that you want to be
High-Priority).
3. Hold the GREEN wire to GROUND until the light flashes once (~3 seconds).
4. Disconnect wires when finished programming.
-4-
If you have any questions concerning this or any other product,
please contact our
Customer Service Department
at (585) 226-9787.
If a product must be returned for any reason, please contact our Customer Service Department to
obtain a Returned Material Authorization number (RMA #) before you ship the product back.
Please write the RMA # clearly on the package near the mailing label.
LED FIVE YEAR LIMITED WARRANTY
The manufacturer warrants this LED light against factory defects in material and workmanship for five years
after the date of manufacture. The owner will be responsible for returning to the Service Center any
defective item(s) with the transportation costs prepaid. The manufacturer will, without charge, repair or
replace
at its option
, products, or part(s), which its inspection determines to be defective. Repaired or
replacement item(s) will be returned to the purchaser with transportation costs prepaid from the service
point. A copy of the purchaser's receipt must be returned with the defective item(s) in order to qualify for the
warranty coverage. Exclusions from this warranty include, but are not limited to, domes, and/or the finish. This
warranty shall not apply to any light, which has been altered, such that in the manufacturer's judgment, the
performance or reliability has been affected, or if any damage has resulted from abnormal use or service.
There are no warranties expressed or implied (including any warranty of merchantability or fitness), which
extend this warranty period.
The loss of use of the product, loss of time, inconvenience, commercial loss or
consequential damages, including costs of any labor, are not covered
. The manufacturer reserves the right
to change the design of the product without assuming any obligation to modify any product previously
manufactured.
This warranty gives you specific legal rights. You might also have additional rights that may vary from state to
state. Some states do not allow limitations on how long an implied warranty lasts. Some states do not allow
the exclusion or limitation of incidental or consequential damages. Therefore, the above limitation(s) or
exclusion(s) may not apply to you.
SYNCHRONIZATION
You can synchronize up to ten lights with compatibility.
DO NOT CONNECT WHITE WIRES UNTIL PROGRAMMING HAS BEEN COMPLETED
FOR ALL LIGHTS!!
1. Power up the first unit and select a pattern. Touch and release the green wire to ground
to change patterns.
2. Program the second light for the
same
Pattern
.
3. If applicable, program the
Phase
of the second light.
Lights set for the SAME phase flash
together (simultaneous).
Lights set for DIFFERENT phases
flash opposite one another (alternate).
4. After programming all lights, tie off the green wires and connect the white wires
together.
5. Test lights by applying power to all of them at the same time.
DUMMY HEAD MODE
To utilize this light with an external flasher, place the light in “Dummy Head” mode by
keeping the GREEN wire permanently connected to GROUND. Both Enable wires will be
placed into in a steady burn mode that is compatible with external flashers.
NOTE: Heads MUST be flashed at 50% or lower total on time. They can be pulse width
modulated as low as 15% and at 100hz or higher.
