Micro-Star™ DLITDC Series
Low Profile Dual-Color LED Auxiliary Light
PLIT619 REV. - 3/29/22
IMPORTANT:
Please read all of the following instructions before installing your new
light. Failure to follow these safety precautions may result in damage to your light or
vehicle and may result in serious injury or death to you and your passengers.
WHITE: Connect to White wires from other S-LINK lights
for synchronization
(Cut short if not using)
(Also used during Programming)
YELLOW/BLACK: Highest Priority
Function/Color/Enable 2
GREEN: Touch and release to Ground for programming
(Cap off after programming)
BLACK: Connect to Negative terminal
of battery
YELLOW/GREEN: Low Priority
Function/Color/Enable 1
BATTERY
(10-16 VDC)
•
Installer must have firm knowledge of vehicle electrical systems and emergency
equipment.
It is the sole responsibility of the installer to ensure the warning light is
secure. The manufacturer assumes no responsibility for the secure mounting of
this light.
•
If you need to drill any holes when installing this light, please take care to check that
BOTH SIDES of your drilling surface are clear from obstructions.
•
Choose a mounting location away from any air bag deployment areas.
•
Controls should be placed within convenient reach of the driver.
•
Use only soap and water when cleaning product. Use of other chemicals may discolor
Installation Notes
Wiring Notes
When wiring your lights, it is recommended that you take the following
precautions to reduce any Electromagnetic Interference (EMI).
•
Keep LED modules and any radios as far away from each other as possible.
•
Separate the radio wires and the LED wires.
•
Any excess wires should be cut short.
•
The Ground wire, Power wire, and Synchronization wire should be bound tightly
together as they run from light to light, through your switchbox, and to the battery.
•
Do not ground each unit independently to the chassis
. Run the ground for each
unit in a “bus” like structure, to the negative terminal on the battery.
Note:
The total wire length between the two farthest units should be no more than 40 feet.
5
A
M
P
-2-
Programming, Functionality, and Operation
The recommended first step is to identify what color is defaulted to each input. To do this:
•
Connect the BLACK wire to Ground.
•
Touch only one of the Enable wires to Power and note which color is activated.
•
Repeat for each Enable wire.
STANDARD PROGRAMMING
Follow the instructions below to program any of the
options listed in the chart the chart to the right. Each
Enable wire is programmed independently.
1. Connect the BLACK wire to Ground.
2. Connect the corresponding Enable wire to Power
(only one at a time)
.
3. Hold (or touch and release) the GREEN wire to
Ground to set the options listed to the right.
4. Disconnect wires when finished programming.
Several mounting brackets are available for various applications where mounting directly to
the surface is not desired. Please visit our website (www.starheadlight.com) for a complete
list of brackets.
For surface mounting, use the
gasket as a template to mark and
drill three holes for the self
tapping screws and wires.
Remove the one gasket slit that is open to
the bottom and ensure it is aligned with
the Gortex™ pad on the rear of the light.
This will allow air to circulate through the
pad, helping reduce condensation.
DO NOT OVER TIGHTEN SCREWS!!
TORQUE TO 10 IN.-LBS.!!
MUST DRILL HOLES THE
SPECIFIED SIZES!!!
MUST USE #6 STAINLESS
STEEL SCREWS!!
Surface Mounting Instructions
Once the wires are run, the use of a small amount of silicone or other similar sealant (not
included) is recommended to seal the wire hole and prevent your wires from becoming
damaged.
Unless you are using the optional shims, this light must be
mounted on a perfectly flat surface!! Failure to do so will
result in damage to the housing and will void the warranty!
If you are installing this light on a curved
surface, it is recommended that you
purchase the #30019-314 Shim Kit and
install the shims as pictured to the right.
Rubber Mounting Gasket
P30047-174
STANDARD PROGRAMMING CHART
