DLXT
Thinline Auxiliary LED Lights
PLIT424 REV. F 4/10/13
DLXT-121*** or DLXT-241***
(12 VDC)
(24 VDC)
DLXT-124*** or DLXT-244***
(12 VDC)
(24 VDC)
P
h
a
s
e
1
F
la
s
h
P
a
tt
e
rn
#
P
h
a
s
e
2
F
la
s
h
P
a
tt
e
rn
#
P
a
tt
e
rn
T
y
p
e
Pattern Description
Shortcut
1
11
A
Fast Singleflash (1.9 CPS)
Pattern 1
(Phase 1)
:
3 sec or 1 flash
Pattern 11
(Phase 2)
:
9 sec or 3 flashes
2
12
B
Flicker flash (1.7 CPS)
3
13
C
Post pop (1.4 CPS)
4
14
D
PSU-flicker (0.4 CPS)
5
15
E
Random (1.9 CPS)
(DEFAULT PATTERN)
6
16
F
Quadflash (1.0 CPS)
Pattern 6
(Phase 1)
:
6 Sec or 2 flash
Pattern 16
(Phase 2)
:
12 sec or 4 flashes
7
17
G
Quadflash
w/Post-Pop (1.0
CPS)
8
18
H
Singleflash (1.0 CPS)
9
19
I
Doubleflash (1.0 CPS)
10
20
J
Delta-Omega (0.3 CPS)
N/A
Steady
(see below)
18 sec or 6 flashes
Pattern Shortcuts:
Hold Green wire to ground for indicated
time.
Steady Burn:
Not in pattern cycle. Only accessible through
shortcut. Hold Green wire to ground for 18
seconds (light will flash 6 times).
You can synchronize up to six
lights with compatibility.
DO NOT CONNECT WHITE WIRES
UNTIL PROGRAMMING HAS BEEN
COMPLETED FOR ALL LIGHTS!!
1. Power up the first unit and select a
Phase 1 pattern. Touch and
release the green wire to ground to
change patterns.
2. Program the second light with
the same
Pattern Type
.
Lights with the SAME phase
flash together (simultaneous).
Lights with DIFFERENT phases
flash opposite one another
(alternate).
3. After programming all lights, tie
off the green wires and connect
the white wires together.
4. Test lights by applying power to all of them at the same time.
Quick Install Guide
Warning
Lights
ON/OFF
Switch
-
Bezel
Ground:
Connect to negative terminal of battery
BLACK
Mounting Surface
Rubber
Mounting
Gasket
IMPORTANT
Foam Compression Gasket
LED Array
GREEN
WHITE
GREEN w/WHITE
Sync:
Attach to White wires from other S-Link Lights for synchronization
Split/Single:
Connect with
Black
to
Ground
for Single Mode
Connect with
Red
to Switched
Power
for Split Mode
5 AMP
FUSE
RED
Power:
Connect to switched power
12VDC or 24VDC
(depends upon model)
BATTERY
Use minimum
18AWG wire
!
Pattern Select:
Touch and release to ground to program
Pattern Programming and Synchronization
Light 1
Light 2
(OFF)
(ON)
Simultaneous Pattern
(Programmed for same Phase)
Light 1
Light 2
Alternating Pattern
(Programmed for opposite Phases)
T
IM
E
Split Mode
Light 1
Back & Forth Pattern
(Programmed for same Phase)
In/Out Pattern
(Programmed for opposite Phases)
(OFF)
(ON)
Light 1
Light 2
Light 2
