-1-
-2-
Red - +12VDC
Black - Ground
Purple - High/Low
Red w/Green Stripe
Pattern Select Wire
(Touch & Release to +12VDC)
PATTERN
SELECT
BUTTON
(Mag Mount
Versions Only)
11. The black wire is the ground lead and should be connected to a good chassis ground.
12. The purple wire is used to select between High or Low power. When the purple wire is
connected to ground, the light will operate under low power (night mode). If you will be
running the light on high power all of the time, simply tape off the end of the purple wire,
leaving it disconnected. If you would like to operate your light on low power all of the time,
connect the purple wire to ground. If you would like to switch between High and Low
power, connect the purple wire to Ground through a second switch.
There is no
High/Low option on the mag mount versions.
13. Connect the red wire to your switch.
Be sure to
use a 10 amp fuse
when connecting the
switch to the positive side of the +12VDC power supply.
Pattern Programming
PLEASE NOTE :
The following steps are to be performed
after the unit has been mounted and after all of the
necessary connections to the flasher have been
made. The Pattern Programming button or Pattern
Programming Wire is normally only used for
programming purposes during installation. Models
with a cig plug will be equipped with a Pattern Select
Button inside the light. Models that are hard wired
will have a red w/green stripe wire that is used for
Pattern Programming.
1. To begin the programming sequence, power up the light so that
it is flashing.
2. To change the flash pattern, briefly touch the Pattern
Select wire to +12VDC and release it (or press and
release the Pattern Select Button), repeating this to
scroll through the patterns listed on the following page.
The cycle will repeat itself after the last pattern.
3. Once you find the pattern you wish to display, leave the
Pattern Select wire disconnected and deactivate the
light. This will store the selected pattern into the
memory.
NOTE:
If at any time you would like to reset the pattern to the factory default (Pattern 5),
simply touch the Pattern Select Wire to +12VDC or press the Pattern Select
Button for four seconds, until the light blinks once, and release it. The default
pattern will be restored. Touching the wire to +12VDC or holding the button for
eight seconds (the light will blink twice) reverts the light to Pattern 19.
Pattern List
Parts List
Outer Dome
910-316-*
Dome Gasket (Neoprene Cord) /ft
30047-64
LED Array
910-D1-1-*
LED Flasher
LDF369
Cig Plug
(Mag Mount Only)
920-10SW
Mag Mount Kit (4 Magnets)
910-177K
Mounting Gasket
920-17-16
* = color
If you have any questions concerning this or any other Star product,
please contact our
Customer Service Department
at (585) 226-9787.
If a product must be returned for any reason, please contact our Customer Service Department
to obtain a Returned Goods Authorization number (RGA #) before you ship the product to Star.
Please write the RGA # clearly on the package near the mailing label.
Mag Mount Versions
If you are mounting the light on the roof of your vehicle, take extreme care to ensure
that the magnet is firmly seated on your roof, and that the pull of the magnet is
sufficient to secure the light in place. Since the composition of the metal in the roofs
of different vehicles may vary, as well as the contour, texture and/or condition, Star
cannot guarantee the ability of the light to remain in place upon a moving vehicle.
It
is the sole responsibility of the owner to ensure the warning light is secure.
Care should be taken when routing the cig plug cord so that it does
not interfere with the proper operation of the driver-side or
passenger-side airbag! Failure to heed this warning may result in
serious or fatal injury.
ONE YEAR LIMITED WARRANTY
The manufacturer warrants each new product, under normal use, against factory defects in material and workmanship
for one year after the date of purchase. The owner will be responsible for returning to the Service Center any
defective item(s) with the transportation costs prepaid. The manufacturer will, without charge,
repair or replace
at
its option
, products, or part(s), which its inspection determines to be defective. Repaired or replacement item(s) will
be returned to the purchaser with transportation costs prepaid from the service point. A copy of the purchaser's
receipt must be returned with the defective item(s) in order to qualify for the warranty coverage.
Exclusions from this warranty include, but are not limited to, bulbs, strobe tubes, domes, and/or the finish. This
warranty shall not apply to any light, which has been altered, such that in the manufacturer's judgment, the
performance or reliability has been affected, or if any damage has resulted from abnormal use or service. This
warranty does not apply to defect or damage occurring as a result of disaster, accident, abuse, misuse, lightning,
power surges, or failure to follow instructions in any enclosed manuals. Any damage or defects occurring as a result
of any unauthorized service or repairs by unauthorized persons shall be excluded from this warranty.
There are no warranties expressed or implied (including any warranty of merchantability or fitness), which extend
this warranty period.
The loss of use of the product, loss of time, inconvenience, commercial loss or
consequential damages, including costs of any labor, are not covered.
The manufacturer reserves the right to
change the design of the product without assuming any obligation to modify any product previously manufactured.
This warranty gives you specific legal rights. You might also have additional rights which may vary from state to
state. Some states do not allow limitations on how long an implied warranty lasts. Some states do not allow the
exclusion or limitation of incidental or consequential damages. Therefore, the above limitation(s) or exclusion(s)
may not apply to you.
1 Slow Warn
2 Alternating Doubleflash, Flicker
3 Sim. Double, Alt. Pre-Pop Triple, Slow Warn
4 Alternating Non-Synch Doubleflash
5
Alt. Triple, Alt. Non-Synch Double, Alt. Quint, Flicker
†
6
Alt. Quadflash, Flicker, Alt. Doubleflash, Flicker
7
Alt. Pre-Pop Quintflash, Alt. Quintflash, Flicker
8 Simultaneous Tripleflash
9 Alternating Quadflash w/Post Pop
10 Simultaneous Quadflash w/Post Pop
11 Alternating Quintflash
12 One Side Steady-----One Side Singleflash
13 Alternating Pre-Pop Quintflash
14 Simultaneous Flicker
15 Alternating PSU Flicker
16 One Side Steady-----Other Side Short-
Long
17 One Side Rapid Fire, Other Pop
18 Comet 1
(not a dimmable pattern)
19 Medium Warn (Alt. Long Singleflash)
††
20 Alternating Short - Alternating Long
21 Slow Warn, Alt. Tripleflash
22 Slow Warn, Super Fast Warn
23 Sim. Doubleflash, Alt. Doubleflash
24 Sim. Doubleflash, Alt. Doubleflash, Flicker
†
Default Pattern 1
††
Default Pattern 2
