Stanley STHT77504-1, Руководство пользователя

Страница: 11 / 196

11
GB
5. Adjust the height of the laser so the center of the
beam is aligned with
a
(Figure
D 2
).
6.
Directly above or below
b
, mark
c
along the
laser beam (Figure
D 3
).
7. Measure the vertical distance between
b
and
c
.
8. If your measurement is greater than the
Allowable Distance Between
b
and
c
for the
corresponding Distance Between
a
and
b
in
the following table, the laser must be serviced at
an authorized service center.
Distance Between
a
and
b
Allowable Distance
Between
b
and
c
30 ′ (9m) 5/32” (4mm)
40 ′ (12m) 7/32” (6mm)
50 ′ (15m) 5/16” (8mm)
Horizontal Beam - Pitch Direction
Checking the horizontal pitch calibration of the
laser requires a single wall at least 30 ′ (9m) long.
It is important to conduct a calibration check using
a distance no shorter than the distance of the
applications for which the tool will be used.
1.
Place the laser against the end of the wall (Figure
E 1
).
2.
Move the Power/Transport Lock switch to the
right (Figure
A 3
) to turn the laser ON in self-
leveling mode and display a horizontal laser beam.
3. At least 30′ (9m) apart along the laser beam,
mark
a
and
b
.
4.
Move the laser to the opposite end of the wall
(Figure
E 2
).
5. Position the laser toward the first end of the same
wall and parallel to the adjacent wall.
6. Adjust the height of the laser so the center of the
beam is aligned with
b
.
7. Directly above or below
a
, mark
c
along the
laser beam (Figure
E 3
).
8.
Measure the distance between
a
and
c
.
9. If your measurement is greater than the
Allowable Distance Between
a
and
c
for the
corresponding Distance Between
a
and
b
in
the following table, the laser must be serviced at
an authorized service center.
Distance Between
a
and
b
Allowable Distance
Between
a
and
c
30
′
(9m) 5/32” (4mm)
40
′
(12m) 7/32” (6mm)
50
′
(15m) 5/16” (8mm)
Vertical Beam - Plumb
Checking the vertical (plumb) calibration of the
laser can be most accurately done when there is
a substantial amount of vertical height available,
ideally 30
′
(9m), with one person on the floor
positioning the laser and another person near a ceiling
to mark the position of the beam. It is important to
conduct a calibration check using a distance no
shorter than the distance of the applications for which
the tool will be used.
1.
Place the laser at least 3.28 ft (1.0m) from a door
jamb (Figure
F 1
).
2. Move the Power/Transport Lock switch to the
right (Figure
A 3
) to turn the laser ON in self-
leveling mode and display a horizontal laser beam.
3. Press once to display the vertical beam .
4. Aim the vertical laser beam toward the door jamb.
5. Along the bottom of the laser beam, mark three
locations
a
,
b
, and
c
; where
b
is midway
between
a
and
c
.
6.
Where the top of the laser beam appears at the
top of the door jamb, mark
e
.
7. Move the laser to the opposite side of the door
jamb (Figure
F 2
).
8. Align the bottom of the laser beam with
a
,
b
,
and
c
.
9. Where the top of the laser beam appears at the
top of the door jamb, mark
f
.
10.
Measure the distance between
e
and
f
.