Stanley STCT1850, Руководство пользователя

Страница: 12 / 40

12
ENGLISH
Assembly
Warning! T o reduce the risk of injury, always re-
move battery from saw before any of the following
adjustment operations.
Installing and removing the battery pack
from the tool
u
WARNING
: Make certain the lock-off button is
engaged to prevent switch actuation before
removing or installing battery.
u
TO INSTALL BATTERY PACK:
Insert battery
pack into tool as shown in figure B. Ensure
battery pack is fully seated and fully latched into
position.
u
TO REMOVE BATTERY PACK:
Depress the
battery release button as shown in figure C and
pull battery pack out of tool.
Supporting large panels / securing work-
piece
u
Support large panels to minimize the risk of
blade pinching and kickback. Large panels tend
to sag under their own weight as shown in
figure D.
u
Supports must be placed under the panel on
both sides, near the line of cut and near the
edge of the panel (figure E).
u
WARNING: TO REDUCE THE RISK OF
INJURY NEVER hold the piece being cut with
your hands or lay it across your leg (figure F).
u
Secure the workpiece to a stable platform as
shown in figure G. It is important to support the
work properly to minimize body exposure, blade
binding, or loss of control.
Cutting depth adjustment - figures H & I
The depth of cut should be set according to the
thickness of the workpiece.
u
Loosen the depth adjustment knob (11) to
unlock the saw shoe (5) as shown in figure H.
u
Move the saw shoe into the desired position.
The corresponding depth of cut can be read
from the scale (14).
u
Set depth adjustment of saw such that one
tooth (15) of the blade projects below the
workpiece (16) as shown in figure I.
u
Tighten the knob to lock the saw shoe in place.
Bevel angle adjustment - figure J
This tool can be set to bevel angles between 0°
and 50°.
u
Loosen the bevel adjustment knob (10) to
unlock the saw shoe (5).
u
Move the saw shoe (5) into the desired
position. The corresponding bevel angle can be
read from the scale (17).
u
Tighten the bevel adjustment knob (10) to lock
the saw shoe in place.
u
Confirm the accuracy of the setting by checking
the bevel angle of an actual cut on a scrap
piece of material.
Shoe adjustment for 90° cuts
The shoe (5) has been set by the factory to assure
that the blade is perpendicular to the shoe at 0°
bevel setting.
If realignment is needed:
u
Adjust the s aw to 0° bevel.
u
Retract blade guard (8).
u
Loosen bevel adjustment knob (10). Place a
square against the blade (7) and shoe (5) to
adjust the 90° setting.
u
Loosen jam nut (18a) and move the adjustment
screw (18b) (inset figure J) so that the shoe will
stop at the proper angle. Retighten jam nut
against the shoe while holding adjustment
screw in position.
u
Confirm the accuracy of the setting by checking
the squareness of an actual cut on a scrap
piece of material.
Attaching and removing the blade - figure
K- L
u
Retract lower guard and assemble blade (7)
and clamp washer (19) as shown in figure K.
u
Depress the spindle lock (12) while turning the
blade bolt (20) with the blade wrench (9) until
the blade lock engages and the blade stops
rotating. Note: Blade wrench is stored on the
saw as shown in figure l.
u
Tighten the blade bolt securely with the blade
wrench.
Note: Bolt has a left-handed thread. To loosen,
turn clockwise. To tighten, turn
counterclockwise.
Note: Never engage the blade lock while the
saw is running, or engage in an effort to stop
the tool. Never turn the tool on while the blade
lock is engaged. Serious damage to your saw
will result.