background image

8

The charging indicator (11) will flash green continuously 

(slowly).

The charge is complete when the charging indicator (11) 

lights green continuously. The charger and the battery can 

be left connected indefinitely with the LED illuminated. The 

LED will change to flashing green (charging) state as the 

charger occasionally tops up the battery change. The 

charging indicator (11) will be 

lit as long as the battery is 

connected to the plugged-in charger.

•  Charge discharged batteries within 1 week. Battery life 

will be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the 

LED glowing indefinitely. The charg

er will keep the battery 

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the 

charging indicator (11) will flash red at a fast rate. Proceed 

as follows:

•  Re-insert the battery (5).

•  If the charging indicators continues flashing res at a fast 

rate, use a different battery to determine if the charging 

process works properly.

•  If the replaced battery charges correctly, the original 

battery is defective and should be returned to a service 

centre for recycling.

•  If the new battery gives the same indication as the 

original battery, take the charger to be tested at an 

authorised service centre.

Note: It may take as long as 60 minutes to determine 

that the battery is defective. If the battery is too hot or 

too cold, the LED will alternately blink red, fast and 

slow, one flash at each speed and repeat

Selecting the direction of rotation (FIG. E)

For drilling and for tightening screws, use forward 

(clockwise) rotation. For loosening screws or removing a 

jammed drill bit, use reverse (counterclockwise) rotation.

•  To select forward rotation

, push the forward/reverse 

slider (2) to the left.

• 

To select reverse rotation, push the forward/reverse 

slider to the right.

•  To lock the tool, set the forward/reverse slider into the 

centre position.

Selecting the torque

This tool is fitted with a collar to set the torque for various 

screwdriving and drilling applications. Large screws and hard 

workpiece materials require a higher torque setting than 

small screws and soft workpiece materials. For the definition 

of the symbol refer to the listing below.

•   For 

drilling in wood, metal and plastics, set the torque 

adjustment collar (4) to the    symbol.

•  For screwdriving, set the collar to the desired setting. If 

you do not yet know the appropriate setting, proceed as 

follows:

  -  Set the torque adjustment collar (4) to the lowest  

    torque setting.

  -  Tighten the first screw.

  -  If the clutch ratchets before the desired result is  

    achieved, increase the collar setting and continue  

    tightening the screw. Repeat until you reach the  

    correct setting. Use this setting for the remaining  

    screws.

Speed selector

• 

For drilling in steel and for screwdriving applications, 

slid

e the speed selector (8) towards the rear of the tool 

(1st gear).

•  For drilling in materials other than steel, slide the speed 

selector (8) towards the front of the tool (2nd gear).

Drilling/screwdriving

•  Select forward or reverse rotation using the 

forward/reverse slider (2).

•  To switch the tool on, press the switch (1). The tool 

speed depends on how far you press the switch.

•  To switch the tool off, release the switch.

LED work light

The LED work light (7) is activated automatically when the 

trigger is 

depressed. The LED work light will illuminate when 

the trigger is partially depressed, before the unit begins 

ru

nning.

ENGLISH    

(Original instructions)

Содержание STCD1081B2














Отзывы: