20
WARNING!
Always attach the product to
the harness. Do not carry it just by hand!
1). To remove the harness from the loop, open the
securing clip (A10).
2). Place the harness so that it runs over the
left shoulder, crossing the chest and back. The
securing clip must be located at the right hip. (See
Fig. 9)
3). Adjust the length of the harness (A8) so that
the hook is approximately 15 cm below your waist;
locate the product to the harness by using the
securing clip ensuring that the angle of the cutting
head is parallel to the surface being cut.
WARNING!
Always attach the product to the
harness. Do not carry it only with your hands.
4). In case of emergency, pull the rope of the quick
release mechanism. The metal locking bar will
be released from the securing clip automatically
because of the weight of the machine, and the
machine will drop away from you. (See Fig. 10b)
4. AUXILIARY HANDLE
Adjust the position and angle of the auxiliary
handle (A15) on the upper shaft.
1). Loosen the bolts on the auxiliary handle (A15)
and adjust the position. (See Fig. 11)
2). Afterward tighten the bolts.
5. STARTING AND STOPPING
GENERAL BEHAVIOUR
1). Check the product as well as accessories for
damage before each use. Do not use the
product if it is damaged or shows wear.
2). Double check that accessories, safety guards
and blades are properly fixed.
3). Always hold the product the product by its
handles. Keep the handles dry to ensure safe
support.
4). Ensure that the air vents are always
unobstructed and clean. Clean them if necessary
with a soft brush. Blocked air vents may lead to
overheating and damage the product.
5). Switch the product off immediately if you are
disturbed while working with it and when other
people enter the working area. Always let the
product come to complete stop before putting it
down.
6). Do not overwork yourself. Take regular breaks
to ensure you can concentrate on the work
and have full control over the product. Always
switch the engine off if you make a break or
move to another area.
7).It is necessary to change the working positions
regularly.
This product is controlled by the control handle. For
operation three steps are necessary:
Firstly, the ignition switch (A19) must be put into its
on position “I”. Then the throttle interlock
(A20) must be pressed to disengage the throttle
trigger. Finally press the throttle trigger (A18).
(See Fig. 12a)
1). Starting
a). Place the product on a flat, stable surface.
Ensure that the attachment in use does not
touch the ground or any objects.
b). Set the ignition switch (A19) to its on position “I”.
(See Fig. 12b)
c). If the engine is cold, move the choke lever (A3)
to the “CLOSE” position
and depress
the primer (A4) with 6 times until fuel is visible. (See
Fig. 12c)
d). If the engine is warm, move the choke lever (A3)
to the “OPEN” position
, do not press
the primer. (See Fig. 12d)
e). Hold the product stable and pull the recoil
starter handle (A7) firmly; repeat until the engine
starts. (See Fig. 12e)
WARNING!
Make sure that the cutting blade
is not touching the ground or other
objects when starting the product!
Allow the recoil starter rope to return slowly and
controlled after each pull!
f). Allow the product to run at idle speed for 10 to 15
G
B
Содержание SPS-750
