Stanley IW16 Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 16

Stanley IW16 Series Скачать руководство пользователя страница 12

12 | IW16 Service Manual

Orientation of Insert Seals

Main Shaft

Idler Gear

Relief Adjustment

Screw

03252

00016

Insert

00717

03252

00717

00016

10.  Inspect the bushings. The insides of the bushings should be gray in color. If yellow-bronze shows, replace the bushing.
11.  Inspect the idler and main shafts for wear. Replace if necessary.
12.  Inspect the gear chamber. The chamber should be polished and not rough or grooved.
13.  Check each gear and insure they have flat, straight tips. Each tooth should have a smooth polish. Replace the gears is damage or cracking is present.

Remove the Valve Spool

1. Remove the roll pin that holds the trigger to the handle.
2. Pull the trigger out of the bottom of the handle.

3. Remove the spring cap, headed push pin, valve spool, relief seat, poppet, springs and spring rest from the handle.
4. Replace exposed seals during reassembly.
Note: During reassembly, ensure that seals 22064, 06533 and 00026 are in their proper position inside the spool cap, as shown in the seal orientation graphic
below.

«
...
10
11
12
13
14
...
»

Содержание IW16 Series

















Отзывы:

Нет отзывов