Stanley ID07 Series, Быстрый старт

Страница: 11 / 16

ID07 User Manual | 11
What is the ID07 Hydraulic Impact Drill?
ID07 is a high torque impact wrench used for tightening nuts, driving lag
bolts or auguring through difficult materials, such as telephone poles.
Specifications
Pressure 2000 PSI (140 BAR)
Flow 4-12 GPM (15-46 LPM)
RPM 7679 @ 12 GPM (46 LPM)
Max. Pressure 2500 PSI (172 BAR)
Max. Relief Pressure 2100 PSI (145 BAR)
Recommended Back
Pressure 250 PSI (17 BAR) - Can be used with higher
back pressures with reduced seal life.
Couplers 3/8 Inch, NPT Pipe Fitting
Port Size -8 SAE O-ring
Tool Weight 7 Lbs. (3.2 Kg)
Tool Size 13 Inches x 5 Inches x 12 Inches
Max. Hydraulic Oil
Temperature 140°F (60°C)
HTMA/EHTMA Category Type II - Category D
Underwater Tool Max.
Depth 1000 Feet (305 M)
Recommended Hose Diameters for Underwater Applications
Depth
8 GPM (30 LPM) 12 GPM (45 LPM)
100 Feet (31 Meters) 5/8 Inches (16 mm) 5/8 Inches (16 mm)
300 Feet (91 Meters) 3/4 Inches (19 mm) 1 Inch (25.4 mm)
600 Feet (183 Meters) 1 Inch (25.4 mm) 1 Inch (25.4 mm)
1000 Feet (305 Meters) 1 Inch (25.4 mm) 1 1/4 Inches (32 mm)
Sound & Vibration Declaration
Measured A-Weighted sound power
level 101.1 dBA
Uncertainty 3.39 dBA
Measured A-Weighted Sound Pressure 93.1 dBA
Uncertainty 3.39 dBA
Values determined according to noise test code given in ISO 15744, 11203
and 3744.
Declared vibration emission value in accordance with EN ISO 28927-2.
Declared Vibration Emission Value: 8.5 m/sec²
Uncertainty 1.74 m/sec²
Parts of an ID07 - Detail A
1 Circuit Type “D” Decal
2 Serial Number & Year of Manufacture
3 Read the Manual Decal (CE Models)
4 CE Decal (CE Models)
Pressure Warning Decal (Non-CE Models)
5 Rotation Direction Decal
6 Sound Power Decal (CE Models)
Electrical Warning Decal (Non-CE Models)
7 Handle
8 Female Hydraulic Coupler
9 Male Hydraulic Coupler
10 Trigger Guard
11 Trigger
12 Impact Mechanism
13 Bit Retainer
14 Tool Name Tag
15 Open Center / Closed Center Decal
16 Rotation Direction Spool
Tool Setup
Do not install or change tool accessories while the
hydraulic power source is connected. Accidental
engagement of the tool can cause serious injury.
Disconnect the hydraulic power source before installing
or changing accessories.
1. Disconnect the tool from the hydraulic power source.
Install the Assist Handle - Detail B
ID07 may be equipped with an assist handle as an accessory (see “ID07
Accessories” on page 12). The assist handle helps to absorb reaction
torque and control the tool. Loss of control can cause personal injury.
STANLEY recommends you use the assist handle whenever possible.
1. Place the assist handle over the hammer case.
2. Tighten the handle.
Set Hydraulic Circuit Type - Detail C
1. Remove the hex plug on the back of the tool handle.
2. Turn the selector screw completely clockwise for open center operation
-OR- completely counter clockwise for closed center operation.
3. Reinstall the hex plug.
Insert Bit - Detail C
Use only impact-rated sockets and accessories. Do not
use sockets or accessories that are in poor condition.
These can crack or fracture during operation and can
become a projectile.
4. Insert the bit while pushing back on the tool retaining sleeve.
5. Lock the tool retaining sleeve in place.
Note: Never operate the tool unless the inserted bit is properly retained. Bits
can become a high velocity projectile.
Choose Drill Rotation Direction - Detail C
6. Push the rotation direction spool left for clockwise bit rotation
-OR-
right for counter clockwise bit rotation.
Tool Operation - Detail D
Connect to a Hydraulic Power Source
1. Using a calibrated flow and pressure gauge, check the output of the
hydraulic power source. Ensure it matches the flow and pressure in
“Specifications” on page 11. Hydraulic fluid must be 50°F or above.
Preheat if necessary.
Note: Check the hydraulic power source once a day. Proper flow and
pressure are critical to maintaining proper tool speed.
2. Ensure that the hydraulic power source is equipped with a relief valve
set to open at the maximum relief pressure, see “Specifications” on
page 11.
3. Wipe hose couplers with a clean, lint free cloth.
4. Connect the return hose to the tool port marked “Out”.
5. Connect the pressure hose to the tool port marked “In”.
Using the Tool