11
GB
4.
Using a target to transfer the front level dot location on the
wall to the floor, mark point P2 on the floor and then point
P3 on the floor
(Figure
J
#1).
5.
Move the laser
to point P2 and align the front level dot to
point P3 again (Figure
J
#2).
6.
Using a target to transfer the front level dot location on the
wall to the floor
, mark
the location of two square beams as
points P4 and P5 on the floor
(Figure
J
#2).
7.
Turn the laser
90° so the front level dot aligns to point P4
(Figure
J
#3).
8.
Mark
the location of the first square beam as point P6 on
the floor as close as possible to point P1 (Figure
J
#3).
9.
Measure the
distance between points P1 and P6
(Figure
J
#3).
10.
If your
measurement is greater than the
Allowable
Distance Between P1 & P6
for the corresponding
Distance (D1)
in the following table, the laser must be
serviced at an authorized service center.
Distance (D1)
Allowable Distance
Between P1 & P6
7.5 m (25’)
2.2 mm (3/32
”
)
9 m (30’)
2.7 mm (7/64
”
)
15 m (50’)
4.5 mm (3/16
”
)
11.
Turn the laser
180° so the front level dot aligns to point P5
(Figure
J
#4).
12.
Mark
the location of the second square beam as point P7
on the floor as close as possible to point P1 (Figure
J
#4).
13.
Measure the
distance between points P1 and P7
(Figure
J
#4).
14.
If your
measurement is greater than the
Allowable
Distance Between P1 & P7
for the corresponding
Distance (D1)
in the following table, the laser must be
serviced at an authorized service center.
Distance (D1)
Allowable Distance
Between P1 & P7
7.5 m (25’)
2.2 mm (3/32
”
)
9 m (30’)
2.7 mm (7/64
”
)
15 m (50’)
4.5 mm (3/16
”
)
Using the Laser
Operating Tips
•
Always mark the center of the beam created by the laser.
•
Extreme temperature changes may cause movement of
internal parts that can affect accuracy. Check your accuracy
often while working.
• If the laser is ever dropped, check to make sure it is still
calibrated.
•
As long as the laser is properly calibrated, the laser is self-
leveling. Each laser is calibrated at the factory to find level
as
long as it is positioned on a flat surface within average ± 4°
of level. No manual adjustments are required.
•
Use the laser on a smooth, flat, level, surface.
Turning the Laser Off
Slide the Power/Transport Lock switch to the OFF/Locked
position (Figure
A
#1a) when the laser is not in use. If the
switch is not placed in the Locked position, the laser will not
turn off.
Using the Laser with Accessories
WARNING:
Since accessories other than those offered by
Stanley have not been tested with this laser, use of
such accessories with this laser could be hazardous.
Only use Stanley accessories that are recommended for use
with this model. Accessories that may be suitable for one laser
may create a risk of injury when used with another laser.
The bottom of the laser is equipped with 1/4-20 and 5/8-11
female threads (Figure
B
) to accommodate current or future
Stanley accessories. Only use Stanley accessories specified
for use with this laser. Follow the directions included with the
accessory.
Recommended accessories for use with this laser are available
at extra cost from your local dealer or authorized service center.
If you need assistance locating any accessory, please contact
your nearest Stanley service center or visit our website:
http://www.2helpU.com
.
Содержание Fatmax FMHT1-77415
Страница 2: ...1b 1a 2 A 1 3 B 1 4 20 5 8 11 x5 x1 x2 x3 x4 5 5 3a 3b 3c 3d Figures 2 ...
Страница 3: ...D C 1 2 3 P1 x x P2 P3 x x P2 P1 x 30 9m 2 1 E ...
Страница 221: ...Notes ...
Страница 222: ... 2017 Stanley Tools Egide Walschaertsstraat 14 16 2800 Mechelen Belgium N498963 Rev C June 2017 http www 2helpU com ...
