Stanley FatMax FMCS701, Оригинальное руководство пользователя

Страница: 17 / 24

17
ENGLISH (Original instructions)
your hand would be less than 6" (152 mm) from the blade, a
clamp or other fixture must be used.
Use the material clamp provided with your saw. To purchase
a material clamp, contact your local retailer or Stanley FatMax
service centre.
Other aids such as spring clamps, bar clamps or C-clamps
may be appropriate for certain sizes and shapes of material.
Use care in selecting and placing these clamps. Take time to
make a dry run before making the cut.
To install clamp (fig. P)
u
Insert the clamp (37) into the hole (19) behind the fence.
The clamp should be facing toward the back of the mitre
saw. The groove on the clamp rod should be fully inserted
into the base. Ensure this groove is fully inserted into the
base of the mitre saw. If the groove is visible, the clamp
will not be secure.
u
Rotate the clamp 180º toward the front of the mitre saw.
u
Loosen the knob to adjust the clamp up or down, then use
the fine adjust knob to firmly clamp the work piece.
Note: Place the clamp on the opposite side of the base when
bevelling. ALWAYS MAKE DRY RUNS (UN-POWERED) BE-
FORE FINISH CUTS TO CHECK THE PATH OF THE BLADE.
ENSURE THE CLAMP DOES NOT INTERFERE WITH THE
ACTION OF THE SAW OR GUARDS.
Adjustments
Your mitre saw is fully and accurately adjusted at the factory at
the time of manufacture. If readjustment due to shipping and
handling or any other reason is required, follow the instruc-
tions below to adjust your saw.
Once made, these adjustments should remain accurate. Take
a little time now to follow these directions carefully to maintain
the accuracy of which your saw is capable.
Mitre scale adjustment (fig. Q1)
Lock the arm in the down position. Unlock the mitre lock
knob (5) and swing the mitre arm until the mitre latch button
(6) locks it at the 0° mitre position. Do not lock the mitre lock
knob. Place a square against the saw’s fence and blade,
as shown. (Do not touch the tips of the blade teeth with the
square. To do so will cause an inaccurate measurement.) If
the saw blade is not exactly perpendicular to the fence, loosen
and move the material fence until the blade is perpendicular
to the fence, as measured with the square. Pay no attention to
the reading of the mitre pointer at this time.
Bevel square to table adjustment (Fig. Q2)
To align the blade square to the table, lock the arm in the
down position with the lock down pin (20). Place a square
against the blade, ensuring the square is not on top of a tooth.
Loosen the bevel lock knob (5) and ensure the arm is firmly
against the 0° bevel stop. Rotate the 0° bevel adjustment
screw with the 1/2" (12.7 mm) socket (not provided) as neces -
sary so that the blade is at 0° bevel to the table, as measured
with the square.
Guard actuation and visibility (Fig. V)
Warning! Pinch hazard. To reduce the risk of injury, keep
thumb underneath the operating handle when pulling the
handle down. The lower guard will move up as the operating
handle is pulled down, which could cause pinching.
The lower guard (4) on your saw has been designed to au-
tomatically uncover the blade when the arm is brought down
and to cover the blade when the arm is raised.
Before each use or after making adjustments, cycle the arm
(un-powered) and make sure the guard opens smoothly and
closes fully. It should not contact the blade. With the arm
up, raise the guard (un-powered) as shown in Figure V and
release. The guard should fully close rapidly.
Do not operate the saw if the guard does not move freely and
fully close rapidly. Never clamp or tie the guard in an open
position when operating the saw.
The guard can be raised by hand when installing or removing
saw blades or for inspection of the saw.
NEVER RAISE THE LOWER GUARD MANUALLY UNLESS
THE BLADE IS STOPPED.
Note: Certain special cuts of large material will require that
you manually raise the guard. Refer to cutting large material
under special cuts.
The front section of the guard is louvred for visibility while
cutting. Although the louvres dramatically reduce flying debris,
they are openings in the guard and safety glasses should
be worn at all times.
Rail Guide
Periodically check the rails (13) for any play or clearance. The
rails can be cleaned with a dry clean cloth.
Cutting Picture Frames, Shadow Boxes And Other
Four-Sided Projects (Fig. R1, R2)
To best understand how to make the items listed here, we
suggest that you try a few simple projects using scrap wood
until you develop a “feel” for your saw.
Your saw is the perfect tool for mitreing corners like the one
shown in Figure R1. Sketch A in Figure R2 shows a joint made
by using the bevel adjustment to bevel the edges of the two
boards at 45º each to produce a 90º corner. For this joint the
mitre arm was locked in the zero position and the bevel ad-
justment was locked at 45º. The wood was positioned with the
broad flat side against the table and the narrow edge against
the fence. The cut could also be made by mitreing right and
left with the broad surface against the fence.