Stafford Instruments ST216 Скачать руководство пользователя страница 7

Страница: 7 / 16

ST216 User Handbook

Page

When not firing there are no indicators lit on
the mimic panel, the run indicator is off and
the display shows the current kiln
temperature.

Altering a program

The controller settings can be reviewed by pressing the

► key.

The first push of the

► key flashes the dedicated program number

display. The required firing program can now be selected with the

▲ &

▼ keys. There are 80 programs available.

Note: holding down the ▲ or ▼ keys causes rapid change of the displayed value.

The next push of the

► key displays ramp

rate 1 in °/HR or FULL. This can be altered
with the

▲ & ▼ keys. The ramp 1 indicator

on the mimic panel will flash. FULL ramps as
fast as possible.

The next push of the

► key displays

temperature t1. This can be altered with the

▲ & ▼ keys. The t1 indicator on the mimic
panel will flash.

The next push of the

► key displays the soak

period in hours:minutes. This can be altered
in the range 00:00 to 99:59 with the

▲ & ▼

keys. The soak period indicator on the mimic
panel will flash.

Note 2: to exit programming without cycling through all of the above steps wait 20 seconds without

pressing any keys - the ST216 will revert to the idle display. Alternatively press the

►

key to exit

programming and to begin firing immediately.

Note 3: the ◄ key can be used to reverse through the programming steps to correct errors or to exit pro-

gramming mode.

Note 1: available ramp rate displays are: End, 1 … 999 & FULL. If full power is required then push the ▲

key until FULL is displayed. To prematurely mark the end of the program push the ▼ key until End is

displayed - this feature can be used in ramp 2 so that only ramp 1 is executed.

The next push of the

► key displays ramp

rate 2 in °/HR or FULL. This can be altered
with the

▲ & ▼ keys. The ramp 2 indicator

on the mimic panel will flash. FULL ramps as
fast as possible.

The next push of the

► key exits programming mode unless program linking is

enabled (see Installation Handbook).

If program linking is enabled then LoFF
(Linking Off) or Lon (Linking On) is displayed.
The link status can be changed with the

▲ &

▼ keys. If LoFF is selected then the next
push of the

► key exits programming mode.

Содержание ST216

















Результаты поиска

Содержание ST216

Отзывы:

Похожие инструкции для ST216

Бренды по названию

Популярные бренды

Stafford Instruments ST216, Руководство пользователя

Результаты поиска

Содержание ST216

Отзывы:

Похожие инструкции для ST216

Бренды по названию

Популярные бренды