Stabila LD 400 Скачать руководство пользователя страница 12

Страница: 12 / 15

Appendix

Stabila LD 400

SLO

FIN

KOR

RUS

CHN

EST

Timer (self-triggering)

1x long: The

symbol is displayed.

The timer is preset to 5 seconds.

The value is increased.

Holding the buttons down increases the rate of
change of the values.
The countdown starts automatically (if the laser is
activated) and then triggers the measurement.

Switching off the beep

Press and hold simultaneously for

5 seconds:

The beep is switched off.
To reactivate it, press and hold for 5 seconds.

Appendix

Display Notices

All display notices are either displayed with

"Error". The following errors can be corrected.

Cause

Correction

204

Calculation error

Repeat procedure

252

Temperature too
high

Let device cool down.

253

Temperature too
low

Warm device up

255

Received signal too
weak, time for a
measurement too
long.

Use a target plate

256

Received signal too
strong

Use target plate (gray
side)

257

Faulty measure-
ment, too much
background light

Use target plate (brown
side)

258

Outside of the range
of measurement

Select measurement
distance within the
range of measurement

Error

Cause

Correction

Error

Hardware error

Should this message
remain active after
switching the instru-
ment off and on several
times, please contact
the dealerhip.

Содержание LD 400
















Результаты поиска

Содержание LD 400

Отзывы:

Похожие инструкции для LD 400

Бренды по названию

Популярные бренды

Stabila LD 400, Руководство по эксплуатации

Результаты поиска

Содержание LD 400

Отзывы:

Похожие инструкции для LD 400

Бренды по названию

Популярные бренды