background image

Do not store the laser when wet. Dry 

the laser and case before putting 

the laser away. 

Do not submerge the laser.

Do not unscrew !

Operating status display and error messages 

via the LEDs

Illuminated 

green

 LED

-> laser in operation

Illuminated 

green

 LED 

 

+ laser beam

 flashing

-> The laser levels itself automatically

Flashing

 

green

 LED 

 

+ laser beam

 flashing

-> The unit is inclined too much 

    + is outside the self-levelling range 

    + the laser cannot level itself automatically

Illuminated

 red 

LED

-> laser in operation

-> battery voltage very low

-> battery replacement required imminently

Illuminated

 red 

LED

 

+ laser beam

 flashing

-> The laser levels itself automatically

-> Battery voltage very low 

-> Battery replacement required imminently

Flashing

 

red

 LED 

 

+ laser beam

 flashing

-> Battery voltage very low

-> The unit is inclined too much 

    + is outside the self-levelling range 

    + the laser cannot level itself automatically

-> The temperature in the unit is over 50°C / 122°F

-> The laser diodes have been switched off to protect 

   against overheating

-> Place the unit in the shade to be able to continue  

    working.

-> The laser is not working

Only LA-180L: 

The LEDS flash red

                     + green

 + laser cannot be seen

The LEDS

 flash red + 

green alternately 

The LEDS 

flash 

3 x during 

a period of 3 seconds

The appliance is in registration mode

The registration was successful

Содержание LA 180L
















Отзывы: