s
afeTy
P
reCauTions
OWNER RESPONSIBILITIES
To ensure safe and trouble-free operation of this equip-
ment, the operator must have a thorough understanding of
safety precautions and operating procedures . Therefore, it
is the responsibility of the equipment owner to ensure that
every operator of this equipment:
1 . Reads the Safety Precautions section of this manual
and understands the instructions prior to operating
this equipment .
2 . Reads the operating section of this manual and under-
stands all operating procedures prior to operation .
3 . Observes the fundamental regulations pertaining to
workers’ protection and accident prevention .
4 . Observes additional rules and regulations in effect at the
equipment owner’s place of business .
Once trained, equipment operators should be continually
evaluated to ensure they fully understand safety precautions and
operating procedures .
Following simple safety guidelines can further reduce
hazard risks .
CAUTION
Please read all information regarding safety
precautions . Failure to follow these procedures
may void your warranty .
SAFETY
1 . Check the AC cable for nicks and cuts (regularly check
the cable to ensure it is in good condition) .
2 . Ensure that the correct supply voltage is available before
switching on the unit .
3 . It is recommended that the unit be connected to an elec-
trical supply that is surge protected and in compliance
with local codes .
4 . The unit is fitted with a standard three-prong plug with a
15A circuit breaker .
5 . There are no serviceable parts in the fan unit .
6 . Do not pull the portable unit by the electrical cable or
the hose .
7 . Be sure the voltage being used corresponds with the volt-
age on the machine parts . The standard motors are 115
V, 1 Ph, 50/60 Hz and 240 V, 1 Ph, 50/60 Hz .
General Safety
1 . The On/Off switch for both units is located on the cylin-
drical enclosure at the end furthest from the blower
hose . Press the RED button for OFF and the GREEN but-
ton for ON .
2 . Be sure the portable unit stands level on the four bottom
feet .
3 . If the unit has been fitted with a speed controller, adjust
the speed to your desired level while the unit is off .
4 . Do not remove any guarding or the flexible hose at any
time . Do not allow objects to pass through the guard
while the fan is rotating .
5 . Always switch the unit off at the main electrical supply
and remove the plug before cleaning the Jet-Kleen . Do
not use a pressure washer or steam washer to clean the
unit .
6 . Eye protection should be worn at all times while
operating the unit .
REPLACEMENT PARTS
This unit was designed and engineered with operator
safety and maximum performance as primary objectives .
Substitution of non-OEM parts may jeopardize safety and/or
performance and void your warranty .
i
nsTallaTion
& s
eTuP
The wall mount unit should be located where it will be
most convenient for use, such as an entry/exit point .
Mount the unit with six screws through the holes on the
wall mount (Figure 1, page 3) . The bottom (hose end) of the
unit should be about 51-52” above the surface .
The portable model should be placed so the four legs
are in contact with a flat surface .
Both units should be plugged into an appropriate
grounded outlet .
Press the green button on the on/off switch to operate
the Jet-Kleen . The red button shuts it off .
Figure 2. With locking ring unscrewed (as pictured) pull quick-release fitting
toward hose.
Locking ring
Quick-release fitting
Gun
assembly
Swivel connector
SPECIALIZED
SAFETY
PRODUCTS
A Division of The A.W.T. World Trade Group
p
S
S
4321 N. Knox Ave., Chicago, IL 60641 USA
773.777.7100 • Fax:773.777.0909
sales
@
specializedsafetyproducts
.
com
www
.
specializedsafetyproducts
.
com
J
et
-K
leen
tm
4
Installation & Operation Manual
A Product of
