manualshive.com logo in svg

SSANGYONG korando C200, Руководство по обслуживанию

Поделиться
Скачать
SSANGYONG korando C200 Скачать руководство пользователя страница 36

02-38

korando 2010.10

8625-03

AIR BAG SYSTEM

Longitudinal and orthogonal acceleration sensors
Two inflator circuits with energy reserve function for driver and passenger front air bags
Two inflator circuits without energy reserve function for front belt pretensioner
Two inflator circuits without energy reserve function for front side air bag
Two inflator circuits without energy reserve function for curtain air bag
Warning lamp indicating system fault
One service communication interface (KWP2000)
Two SIS (Side Impact Sensor) interfaces
Two FIS (Front Impact Sensor) interfaces
Crash output interface

-
-
-
-
-
-
-
-
-
-

3) Components

DC/DC converter

▶

4) Function

The DC/DC converter (Combined ASIC) of the power supply has step up and step down 
converters, and supplies the firing voltage for the two firing circuits and the internal operating 
voltage of the SDM. If the internal operating voltage falls below a defined threshold, a reset is 
executed.

Watchdog

▶

The watchdog checks the micro controller (μC) periodically. If there is any fault in the 

micro controller, it will be reset and firing loop will be locked. Then, the warning lamp will come 
on.

Detects crash
Activates the front air bag, side air bag, curtain air bag and belt pretensioners
Monitors the safety system
Indicates system readiness and faults to the driver by means of a fault warning lamp
Facilitates servicing capability via a serial diagnostic communication interfaces
Diagnoses the system including internal system monitoring and ambient sensor monitoring
Automatic activation
Records crash data
Reserves electric energy for deploying the air bag in the event of frontal crash with power 
cut off

-
-
-
-
-
-
-
-
-

2) Major Functions

Содержание korando C200






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды