background image

47

Air Spring Removal and Service - Silver

2 0 0   H o u r   S e r v i c e

A i r   S p r i n g   R e m o v a l   a n d   S e r v i c e   -   S i l v e r

WARNING- EYE HAZARD

Verify all pressure is removed from the fork before proceeding. Depress the Schrader valve again to remove any remaining air pressure. Failure to 

do so can result in injury and/or damage to the fork.

NOTICE

Inspect each part for scratches. Do not scratch any sealing surfaces when 

servicing your suspension. Scratches can cause leaks.
When replacing seals and o-rings, use your fingers or a pick to remove the 

seal or o-ring. Spray isopropyl alcohol on each part and clean with a clean 

lint-free shop towel. 
Apply Liquid-O-Ring PM600 or SRAM Butter grease to the new seals and 

o-rings. If a brush is used to apply grease, confirm there are no loose 

bristles in the grease or on the part.

Unthread the air spring top cap from the upper tube.
The air spring tube is attached to the top cap. Remove the top cap, air 

tube and air spring assembly from the upper tube.
Clean the upper tube threads.

Remove the top cap.

Remove the air spring assembly from the air tube.

PM600

SRAM Butter

24 mm

Содержание Rockshox 30 Gold RL
































































































Отзывы: