The iPAMM is provided for customers to assemble in their rack in order to minimise
the use of valuable RU space and to ensure it is possible to remove an iPAMM for
service. These instructions are intended to make installation an easy process.
If you have difficultly installing an iPAMM Unit please contact SRA for advice.
e: [email protected] | p: +61 2 6298 1855
iPAMM Kit
-
A.
iPAMM Unit (x1),
B.
iPAMM
Stud Plates (x2),
C.
iPAMM Mounting Rails
(x2),
D.
iPAMM Grille (x1)
Hardware
-
E.
M6 x 16 Screws (x6),
F.
M5 Flange Nut (x10),
G.
M5 Contact
Washer (x8),
H.
M5 Locating Washer (x4)
Email - [email protected]
5.A Slide the iPAMM Main Body
into position holding the handle with
one hand, gently lower the iPAMM Main
Body into the front area of the rack with
the other hand supporting the pinchweld
side of the unit.
5.B Gently slide the bottom part of the
iPAMM Main Body closer to the Mounting
rails while keeping the pinch weld just
above the escutcheon plate of the rack
frame.
Ensure that the two rear Mounting Pins
are beneath the iPAMM Mounting Rails.
5.B
Note the pins
6. Once the front of the iPAMM
can drop into the frame of the rack,
push the iPAMM back, ensuring that the
front two Mounting Pins slide under the
iPAMM Mounting Rails.
Once the iPAMM is placed up against the
Mounting Rails, use 2 x Flange Nuts and 2
x Contact Washers, over the third stud
from the bottom (position 3).
7. Slide the iPAMM Top Cover into the
channel. Secure using 2 x Flange Nuts
and 2 x Contact Washers, over the fourth
stud from the bottom (position 2).
8. Place the iPAMM Grille onto the
front of the unit with the return
towards the top. Place the pinch weld
side hard up against bottom of the
IPAMM and frame bottom, then pivot the
grille such that the top return slides
underneath the top cover. It may require
some downward pressure to locate the
lip under the top cover.
9. Secure the iPAMM Grille with 4 x
Flange Nuts and 4 x Contact Washers, on
the top (posiiton 1) and bottom studs
(position 5).
5.A
Mount the unit
6
Use contact washers
7
Fit the top cover
8
Angle the grille
9
Secure the grille
1. Install the iPAMM Mounting
Rails by placing the tabs through the
slots in the Rack Mount Arms as shown.
2. Secure the Mounting Rails to the Rack
Mount Arms using 3 x M6 Screws, repeat
the process with the remaining Mount
Rail on the opposing Mount Arm.
3. Place the Locating Washers
over studs 2 and 4 on both of the Stud
Plates.
Position the 2 x Stud Plates (with the
Locating Washers still in place) into the
front Mounting Rails of the Rack.
4. Secure the 2 x Stud Plates using a
Flange Nut on the 2nd stud (position 4)
from the bottom of each plate.
1
Mount the rails
2
Secure the rails
3
Locate the washers
4
Secure the plate
iPAMM
Installation Manual
Warning: Do not connect the iPAMM to any power source until the
unit is completely installed.
VERSION 2.0
iPAMM
Version 2.0
iPAMM
Version 2.0
Installation Manual
iPAMM
Mounting Kit
Warning: Do not connect the iPAMM to any power source until the
unit is completely installed.
B.
C.
E.
F.
G.
H.
A. NOT SHOWN
D. NOT SHOWN
C.
H.
H.
H.
H.
B.
B.
C. + E.
1.
2.
3.
4.
5.
H. + F.
H.
1.
2.
3.
4.
5.
F. + G.
1.
2.
3.
4.
5.
F. + G.
v2.0
v2.0
1.
2.
3.
4.
5.
F. + G.
