Squire SIT030 Скачать руководство пользователя страница 3

       

Installation & Operation Manual

Please read before proceeding

Installer – 

Read all instructions before 

installing.  Perform steps in the order given.

Have this indirect water heater serviced/
inspected by a qualified service technician, at 
least annually.

Failure to comply with the above could result 
in severe personal injury, death or substantial 
property damage.

Failure to adhere to the guidelines on this 
page can result in severe personal injury, 
death, or substantial property damage.

When servicing the indirect water heater –

• To avoid severe burns, allow the appliance to cool 
  before performing maintenance.

Indirect water heater operation –

• Should overheating occur or gas supply fail to shut off, 
 do not turn off or disconnect electrical supply to 
  circulator.  Instead, shut off the gas supply at a location 
  external to the appliance.

• Do not use this appliance if any part has been under 
  water.  The possible damage to a flooded appliance can 
  be extensive and present numerous safety hazards.  Any 
  appliance that has been under water must be replaced.

When calling or writing about the appliance 
– Please have the indirect water heater model 
and serial number from the indirect water 
heater rating plate.

Consider piping and installation when 
determining appliance location.

Any claims for damage or shortage in 
shipment must be filed immediately 
against the transportation company by the 
consignee.

Factory warranty (shipped with appliance) 
does not apply to appliances improperly 
installed or improperly operated.

If the information in this manual is not 
followed exactly, a fire or explosion may 
result causing property damage, personal 
injury or loss of life.

This appliance MUST NOT be installed in 
any location where gasoline or flammable 
vapors are likely to be present.

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electric switch; do not 
use any phone in your building.
•  Immediately call your gas supplier from a 
neighbor’s phone.  Follow the gas supplier’s 
instructions.
• If you cannot reach your gas supplier, call 
the fire department.

 WARNING

 NOTICE

 WARNING

 WARNING

Hot Water Can Scald!

• 

Water heated to temperatures for clothes washing, dish washing, and other sanitizing needs can 

 

scald and cause permanent injury.

•  Children, elderly, and infirm or physically handicapped persons are more likely to be 

 

permanently injured by hot water.  Never leave them unattended in a bathtub or shower.  

 

Never allow small children to use a hot water tap or draw their own bath.

 

• 

If anyone using hot water in the building fits the above description, or if state laws or local 

 

 

codes require certain water temperatures at hot water taps, you must take special 

  precautions:

 

 

• 

Use lowest possible temperature setting.

    •  Install some type of tempering device, such as an automatic mixing 

 

 

 

valve, at hot water tap or water heater.  Automatic mixing valve must be selected and 

 

 

 

installed according to valve manufacturer’s recommendations and instructions.

• 

Water passing out of drain valves may be extremely hot.  To avoid injury:

 

• 

Make sure all connections are tight.

 

• 

Direct water flow away from any person.

Protection Must Be Taken Against Excessive Temperature and Pressure!

--Installation of a Temperature & Pressure (T&P) relief valve is required.

3

The following chart details the relationship of water temperature 
and time with regard to scald injury and may be used as a 
guide in determining the safest water temperature for your 
applications.

APPROXIMATE TIME / TEMPERATURE 

RELATIONSHIPS IN SCALDS

120°F

More than 5 minutes

125°F

1 1/2 to 2 minutes

130°F

About 30 seconds

135°F

About 10 seconds

140°F

Less than 5 seconds

145°F

Less than 3 seconds

150°F

About 1 1/2 seconds

155°F

About 1 second

•  Installation and service must be performed by a qualified 
installer, service agency, or the gas supplier.

Содержание SIT030

























Отзывы: