background image

20

Maintenance

Cooling Tower Cleaning:

Any evaporative-type cooling tower must be thoroughly cleaned on 
a regular basis to minimize the growth of bacteria, including Legio-

nella Pneumophila, to avoid the risk of sickness or death. Service 
personnel must wear proper personal protective equipment during 

decontamination. Do NOT attempt any service unless the fan motor 

is locked out.

Operators of evaporative cooling equipment, such as water cooling tow-
ers, should follow maintenance programs which will reduce to an abso-
lute minimum the opportunity for bacteriological contamination.  Public 
Health Service officials have recommended that “good housekeeping” 
procedures be followed, such as:  regular inspections for concentrations 
of dirt, scale, and algae; periodic flushing and cleaning; and the following 
of a complete water treatment program including biocidal treatment. See 

Tower Startup

 instructions on page 12.

The visual inspection should take place at least once a week during the 
operating season. The periodic flushing and cleaning should be done be-
fore and after each cooling season, but in any event at least twice a year. 
The louvers, drift eliminators, and easily accessible fill surfaces should be 
flushed by use of a moderate-pressure water nozzle, being careful not 
to cause physical damage. A reliable water treatment program should be 
installed and maintained. Filtration devices may be employed to reduce the 
suspended solids concentrations, thus increasing the effectiveness of the 
water treatment program. See 

Tower Startup

 instructions on page 12.

Blowdown:

A cooling tower cools water by continuously causing a portion of it to 
evaporate. Although the water lost by evaporation is replenished by the 
makeup  system,  it  exits  the  tower  as  pure  water—leaving  behind  its 
burden of dissolved solids to concentrate in the remaining water. Given 
no means of control, this increasing concentration of contaminants can 
reach a very high level.

In order to achieve water quality which is acceptable to the cooling tower 
(as well as the remainder of your circulating water system), the selected 
water  treatment  company  must  work  from  a  relatively  constant  level  of 

 

Warning

Содержание MARLEY AV 98-1514E

































Отзывы: