Sproutwell Small Circle Скачать руководство пользователя

Страница: 3 / 51

Free Tool

Assembly and Maintenance Advice

Tools Provided:

Component required but not provided:

Neutral Silicone Sealant

Tools Required when Assembly (Not Provided)

Assembly at least by two Persons

1. For safety purposes, we strongly recommend that the product will be assembled by at least two people.

2. Some parts have sharp edges. Please be careful when handling components. Always wear gloves, shoes

and safety goggles during assembly.

3. DO NOT climb or stand on the roof, heavy articles should not be leaned against the greenhouse.
4. Keep roof and gutter clean of snow,dirt & leaves. Large amounts of snow on roof can damage the product,

making it unsafe to stand below or nearby.

5. When your product needs cleaning, use a mild detergent solution and rinse with cold clean water.

Do not use acetone, abrasive cleaners or other special detergents to clean the panels.

(Suitable for Polycarbonate)

Содержание Small Circle




















































Результаты поиска

Содержание Small Circle

Отзывы:

Похожие инструкции для Small Circle

Бренды по названию

Популярные бренды

Sproutwell Small Circle, Руководство по сборке

Результаты поиска

Содержание Small Circle

Отзывы:

Похожие инструкции для Small Circle

Бренды по названию

Популярные бренды