background image

 

 

DANGER: 

SPRAYING SYSTEMS CO. STRONGLY 

RECOMMENDS THE USE OF APPROPRIATE 

SAFETY EQUIPMENT WHEN WORKING WITH 

POTENTIALLY HAZARDOUS CHEMICALS. SEE YOUR 

CHEMICAL’S MSDS SHEET FOR ALL SAFETY MEASURES 

RELATING TO YOUR CHEMICAL.  

This equipment includes but is not limited to: 

 

Protective hat 

 

Safety glasses or face shield 

 

Chemical-resistant gloves and apron 

 

Long sleeve shirt and long pants 

Always remember to carefully read the chemical 

manufacturer’s label and follow all directions. 

WARNING: OPERATING MOTOR HAND-WHEEL 

NOTE: THAT UNDER NO CIRCUMSTANCES 

SHOULD ANY ADDITIONAL LEVER DEVICE SUCH 

AS A KEY WHEEL OR WRENCH BE APPLIED TO THE 

MOTOR HAND-WHEEL. THIS MAY CAUSE DAMAGE TO 

THE MOTOR OR THE TANK WASHER

.

 

MAINTENANCE

 

It is your responsibility to regularly inspect and make 

necessary repairs to this product in order to  

maintain proper operation.   

It is recommended that the bushings and seals be 

inspected every 1000 hours of operation or sooner  

if excessive leakage of the seals occurs. 

REMOVAL AND REPLACEMENT OF SPRAY NOZZLES 

(ITEM 30 ON PARTS LIST DRAWING PL 290E-EP) 

Make sure the unit is completely disconnected from the 

air source before attempting to service nozzles. 
1.

 

Unscrew spray nozzles (30) from nozzle hub (29) 

and inspect for plugging and wear. 

2.

 

If a nozzle is plugged or partially plugged, clean 

out the orifice and inlet area with a wooden 

toothpick or other relatively soft probe. 

Screwdrivers, wire or other hard metal items 

should not be used since they may scratch and 

severely damage the orifice. 

3.

 

If the nozzles need replacement, obtain new 

nozzles. 

4.

 

Replace spray nozzles (30) in nozzle hub (29) by 

tightly screwing them in. 

REMOVAL AND REPLACEMENT OF ELECTRIC MOTOR 

DRIVE (ITEM 13 ON PARTS LIST PL 290E-EP) 

1.

 

Unscrew (clockwise-left hand thread) rotary 

housing plug (31), and slide nozzle hub bushings 

(23) and nozzle hub (29) off the rotary housing 

(22). 

2.

 

Remove any foreign material from nozzle hub 

gear teeth. 

3.

 

To replace parts, slide one nozzle hub bushing 

(23) over the tube of rotary housing (22) up to 

the shoulder. 

4.

 

Insert second nozzle hub bushing (23) into nozzle 

hub (29) and push nozzle hub onto rotary 

housing tube. 

5.

 

Apply Loctite 243 or 242 to threads of rotary 

housing plug (31) and screw (counterclockwise) 

into rotary housing (29) until it seats firmly. 

6.

 

Torque to 150 lb-ft (203 Nm). 

REMOVAL AND REPLACEMENT OF ELECTRIC MOTOR 

(ITEM 1 ON PARTS LIST PL 290E-EP) 

1.

 

First make sure the unit is completely 

disconnected from the power source. 

2.

 

Unscrew both bolts (12) and lock washers (11). 

This will allow you to remove the motor  

sub-assembly (1). 

3.

 

Loosen set screw (3), slide motor coupler (4) 

from motor shaft to reveal key (2). 

4.

 

Reassemble in reverse order making sure that 

motor coupler (4) aligns with groove pin (7). 

REMOVAL/REPLACEMENT OF O-RINGS IN UPPER  

SHAFT SEAL BODY SUB-ASSEMBLY (5)  

(ON PARTS LIST PL 290E-EP) 

1.

 

If it has not already been done, remove the 

electric motor sub-assembly (1) per the  

previous instructions.  

2.

 

Carefully press out groove pin (7). 

3.

 

Loosen the upper shaft seal body sub-assembly 

(5) and remove it and gasket (6) from shaft. 

4.

 

Replace worn upper shaft seal body  

sub-assembly (5) with new sub-assembly (5). 

Содержание TankJet AA290E-EP Series













Отзывы: