4
WWW.SPORTDOG.COM
KEy DEfINITIONS
HANDHELD RECEIVER:
Receives radio signal from the collar transmitter and shows the location, direction, and
distance to your dog. It is water-resistant, but should not be submerged.
TRANSmITTER CHANNEL BUTTON:
Toggles between available channels for
pairing with collar transmitters. Up to
nine collar transmitters can be paired
with one receiver.
TRANSmITTER CHANNEL DISPLAy:
Shows the channel number for the
current collar transmitter being tracked.
POWER/STANDBy INDICATOR LIGHT:
Indicates if the handheld receiver is
powered ON or is in Standby Mode. If
RED, the receiver has a low battery.
Change the battery as soon as possible.
ON/Off BUTTON:
Press and hold this
button until handheld receiver emits
an ascending tone to power ON or a
descending tone to power OFF.
VOLUmE BUTTON:
Toggles among
mute, vibration, and volume levels.
COPy BUTTON:
Puts the handheld
receiver into Copy Mode allowing you
to copy transmitters from one receiver
to another.
POINTING INDICATOR LIGHT:
Indicates the dog is steady on point. When the dog starts moving again, the light
goes out.
TREEING INDICATOR LIGHT:
Indicates the dog is treeing. When the dog starts moving again, the light goes out.
BARKING INDICATOR LIGHT:
Indicates the dog is barking at a certain interval and volume. When the barking
stops, the light goes out.
TRANSmITTER LOW BATTERy INDICATOR LIGHT:
Indicates that the battery in the collar transmitter is low.
Change the transmitter’s batteries as soon as possible.
SIGNAL STRENGTH INDICATOR:
Indicates the estimated distance to the collar transmitter.
TRACKING SIGNAL DISPLAy:
Indicates the direction of the collar transmitter. Lights GREEN when searching
and turns RED when collar transmitter position is fixed.
EXTERNAL ANTENNA PORT:
Connects optional antennae to the handheld receiver to increase range.
COLLAR TRANSmITTER:
Transmits a radio signal with status to the paired handheld receiver(s). It is waterproof and
can be submerged in water.
GREEN LED:
Indicates the collar
transmitter is powered and
functioning correctly.
RED LED:
Indicates the battery in the
collar transmitter is low. Change the
transmitter’s battery as soon as possible.
BLUE LED:
Blinks at regular intervals
to give better visibility to the dog in
low-light conditions.
TRANSMITTER
CHANNEL BUTTON
TRANSMITTER
CHANNEL DISPLAY
POWER/STANDBY
INDICATOR LIGHT
ON/OFF BUTTON
VOLUME BUTTON
COPY BUTTON
TREEING
INDICATOR LIGHT
TRACKING SIGNAL
DISPLAY
TRANSMITTER
LOW BATTERY
INDICATOR LIGHT
POINTING
INDICATOR LIGHT
BARKING
INDICATOR LIGHT
SIGNAL STRENGTH
INDICATOR
BLUE LED
RED LED
BLUE LED
GREEN LED
PREPARE THE HANDHELD RECEIVER
You must complete these steps prior to using this device for the first time.
TO INSTALL OR CHANGE THE BATTERy IN THE HANDHELD RECEIVER:
1. Using a coin, open the battery cover by turning the screw anti-clockwise.
Use a coin or similar item to open the battery cover. Be careful
with a screwdriver, as excessive force may damage the threads.
2. Remove the spent battery by pulling up the rubber flap. Be sure to recycle or properly dispose of
the spent batteries.
3. Place the new battery in the battery slot correctly aligned with the negative (-) and
positive (+) markings.
Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
4. Carefully fit the battery cover and tighten the screw by turning it clockwise with a coin until it is firmly
in place.
Do not replace batteries or turn off the handheld receiver when the dog is in the field
with the collar transmitter as the pairing to the collar will be lost. If the collar transmitter
is in use, you have one minute to change the receiver’s battery without breaking the
pairing to the handheld receiver.
Note: For best performance, do not use rechargeable batteries. Always use new batteries. The handheld receiver
requires one (1) CR123 battery.
TO TURN THE HANDHELD RECEIVER ON:
Press and hold the ON/OFF button until the
Signal Strength Indicator
lights from bottom to top. The handheld
receiver will beep twice and the
Power/Standby Indicator
light will start blinking.
STE
P
::
01
