14
1-800-732-0144
WWW.SPORTDOG.COM
15
matCH tHe CoLLar reCeIVer anD remote tranSmItter
To match the Collar Receiver to work with a new Remote Transmitter or to match a new Collar
Receiver to work with your existing Remote Transmitter:
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off after 4-5
seconds. If the On/Off Button is released too early, the Receiver Indicator Light will begin flashing as
normal. If this occurs, start over from
A
.
C. After the Receiver Indicator Light has turned off, release the On/Off Button.
D. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light
flashes 5 times. Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been
matched and will begin flashing as normal. If the Receiver Indicator Light does not flash 5 times,
start over from
A
.
proGram tHe SyStem for tWo or tHree-DoG operatIon
SportDOG
™
Add-A-Dog
®
Collar Receiver(s) must be purchased to train additional dogs.
Please refer to the back cover for compatible Add-A-Dog Collar Receivers for this system.
1. Program the Remote Transmitter to mode 3 or 4 (see page 13).
2. Program the first Collar Receiver.
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off
after 4-5 seconds. If the On/Off Button is released too early, the Receiver Indicator Light will
begin its normal flashing. If this occurs, start over from
A
.
C. After the Receiver Indicator Light has turned off, release the On/Off Button.
D. Press and hold the
Upper Button
on the Remote Transmitter until the Receiver Indicator Light
flashes 5 times. If the Receiver Indicator Light does not flash 5 times, start over from
A
.
3. Program the second Collar Receiver using
A
through
D
above, but using the
Lower Button
in
place of the Upper Button.
4. Program the third Collar Receiver using
A
through
D
above, but using the
Side Button
in place of
the Upper Button.
CHanGe ID CoDeS
An ID Code is the signal identification between the Remote Transmitter and Collar Receiver. Each is
programmed in 1 of 2,000 ID Codes from the factory. The FieldTrainer
®
425 and 425S have the flexibility
to program two or more Remote Transmitters to the same ID Code, allowing them to both control one
Collar Receiver. There are 64 programmable ID Codes available.
TO MANUALLY PROGRAM A REMOTE TRANSMITTER’S ID CODE FOLLOW THESE STEPS:
1. Turn the Intensity Dial to V/T, and then press and release the Mode Button on the back of your
Remote Transmitter. This does not change the mode, so the current mode will still be active
after the ID change is complete.
2. Once the Mode Button is released, the Transmitter Indicator Light will illuminate solid green and
stay on for 15 seconds.
3. While the green Indicator Light is on, turn the Intensity Dial to select the 1st digit of the ID and then
press and release the Side Button. The green Indicator Light will flash rapidly confirming selection.
S
TE
P
::
06
S
TE
P
::
0
7
S
TE
P
::
08
4. Again, while the green Indicator Light is on, turn the Intensity Dial to select the 2nd digit of the ID and then
press and release the Side Button. The green Indicator Light will flash rapidly confirming selection. The
2nd digit is optional and, if not desired, wait until the green light turns off and refrain from pressing
the Side Button.
5. At the end of 15 seconds, or after the second press of the Side Button, the green Indicator Light will turn off
and the ID of the unit will be updated. At this point, the unit will be in the same mode it was in prior
to setting the ID.
6. Upon changing the ID Code, you will need to match the Collar Receiver to the Remote Transmitter
(see STEP 6 on page 14).
TO RETURN THE UNIT TO THE FACTORY ID FOLLOW THESE STEPS:
1. Turn the Intensity Dial to V/T, and then press and release the Mode Button on the back of your
Remote Transmitter. This does not change the mode, so the current mode will still be active after
the ID change is complete.
2. Do not press any buttons and wait until the green Transmitter Indicator Light turns off.
3. You will need to match the Collar Receiver to the Remote Transmitter (see STEP 6 on page 14).
aCCeSSorIeS
To purchase additional accessories for your SportDOG Brand
®
FieldTrainer
®
425 and 425S, contact the Customer
Care Center at 1-800-732-0144 or visit our website at www.sportdog.com to locate a retailer near you.
Component
Part Number
3
⁄
4
” Black Collar Strap
SAC00-10816
3
⁄
4
” Blaze Orange Collar Strap
SAC00-10815
3
⁄
4
” Blue Collar Strap
SAC00-11921
3
⁄
4
” Green Collar Strap
SAC00-10817
3
⁄
4
” Red Collar Strap
SAC00-11820
3
⁄
4
” White Collar Strap
SAC00-12796
3
⁄
4
” Yellow Collar Strap
SAC00-12795
Collar Receiver (does not include collar strap)
SDT00-13858
SD-425
SDT00-13861
SD-425S
Remote Transmitter Only
SDT00-13857
Remote Transmitter with Lanyard
SDT54-13889
Contact Points (Short)
SAC00-12571
Contact Points (Long)
SAC00-12570
Battery Kit (Collar Receiver)
SAC54-13735
Battery Kit (Remote Transmitter)
SAC54-13734
Wall Charger
SAC00-13736
Accessory Pack (includes screws and Charging Jack covers)
SAC00-14008
400-1511.indd 14-15
8/23/12 8:52 AM
